POWERTEC 71007 Interruttore a paletta da 110 V a 220 V per elettroutensili adatto a sega da banco, banco fresa, trapano a colonna, sega da banco, sega a nastro

Name: POWERTEC 71007 Interruttore a paletta da 110 V a 220 V per elettroutensili adatto a sega da banco, banco fresa, trapano a colonna, sega da banco, sega a nastro
Brand: POWERTEC
SKU: 0736815005519
Price: 44.82 EUR
Availability: InStock

Brand:POWERTEC

3.6/5

€
44.82

Nota: la piastra dell'interruttore è fissata all'interruttore con hardware M4. Per alcune installazioni sarà necessario l'hardware 6-32 (vite e dado). NOMINALE: interruttore intelligente monofase, doppia tensione 110/220 volt, 2 HP/35 A a 120 volt; 3 HP/20 ampere a 230 volt

Quantity

Aggiungi al carrello Compra subito

EAN: 0736815005519

Categories: Prodotti industriali e scientifici, Elettrico industriale, Controlli e indicatori, Interruttori industriali, Interruttori di base,

Actuator Type	Push Button
Brand	POWERTEC
Connector Type	Screw
Country of Origin	China
Current Rating	35 Amps
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	3 x 2 x 2.25 inches
Item model number	71007
Manufacturer	Southern Technology LLC
Material	Metal
Mounting Type	PCB Mount
Operating Voltage	120 Volts
Operation Mode	ON-OFF
Product Dimensions	3 x 2 x 2.25 inches; 9.88 Ounces
Switch Type	Toggle

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Darren Willis

Nice Replacement Switch

Needed to replace a damaged on/off switch on my drill press. This switch feels pretty robust and should last. Installed using a 4 x 2 handy box with a handy box extension. The rear opening of the extension had to be ground down about 1/16" to accommodate the body of the switch. Just remove the metric machine screws and nuts that came with the switch and replace with 6 x 32 machine screw anywhere from 1/2" to 1" long will do.

Scritto da: Andrew Werst

Functional and simple, but consider the magnetic switch

Simple design and should work for most applications, but one safety concern. This design is simple to wire and will work 120/240v split phase (standard us residential) The main potential safety issue is this switch is purely a mechanical switch. Not magnetic hold safety. So if you were to pop a breaker then turn the breaker back on the machine will start back up. Larger machines and/or safety critical devises should have this to prevent the machine from potentially starting up by unexpectedly when you are away from the machine or some one else is near by unaware. This could also potently cause contacts internally to fuse and get stuck switch on. Overall this should work for most light duty non commercial applications with minimal risk. If you have lots of people working around the the devise, large powerful machines or safety critical should look at there alternative version

Scritto da: Animal1971

Very happy!!

This is a great addition to my table saw. Nice positive buttons. I used ring connectors and an electrical box to mount it tip: Do not use walmart electrical connectors as the metal is too thin to keep wies connected.

Scritto da: Ron

Low profile, works really fast for off.

It's not a grounded switch, not the worst but can ground before or after to compensate.

Scritto da: Anthony

I just needed the inside

A Fine switch. I am replacing this exact switch. The last one arced and melted one of the poles(?). I wish I could just replace the small internal piece. All the exterior chunks of plastic are fine. Seems a waste!

Scritto da: Dallas Wright

There was no paddle.

This will work fine, but I specifically ordered this one because I like the slap off paddle feature. It came without a paddle!

Scritto da: Sandy

Connection point poor

Not a bad product, just could be lots better. First, the 4 connection screws are very small and not indicated which one switches what line. A mark like "A"/"A" and "B"/"B" or something like that would be ok. The screws are small, very small. You need to install the hoop style terminal connectors. Also, screws on the back so any connection comes out the sides. If you put this in a standard electrical box, the wires will hit the sides of box. My use was for an older Delta contractor table saw which didn't have a large on/off switch. I made this work for what I needed.

Scritto da: Paul

Powertec 2 Pole Paddle Switch

Well designed switch, just what I needed. However mounting to electrical box as described by others is slightly misaligned but I was able to assemble without modifications. I bought 4 for my shop equipment. Switches are labeled line and load so did not see what others were complaining about. Great switch. As pictured I mounted to a PVC ‘wet and damp location’ Carlon type FS 18 cu in. Box to create a dust proof enclosure. I also installed on a Steel City deep 58371 steel handy box or equivalent without difficulty except for same minor screw alignment.

Scritto da: book mark

switch seems to be well made but time will tell

I bought this switch for my router table I built. The switch was deeper than I thought, lucky I put it in a deep box.

Scritto da: Synonymous

Great but doesn't fit in standard electrical box

It is simple, effective, and affordable. Problem is it doesn't fit in any standard box. It needs an extender as it's quite tall. Another commenter suggested the Taymac SB350S Weatherproof Box but it is too shallow. The screw holes line up but I still had to grind the lip off the access hole in the back and part of the switch itself plus make a wooden extension for it to fit. After that it was fine. There is a model with the box and cord all in one but it is much more expensive and I enjoy modifying stuff so your mileage may vary. Recommended with caveat.

Scritto da: Debra Coutts

Much value for the cost.

The switch installed easy. Great product.

Scritto da: Edwin

Great switch paired with taymac sd350s box - with minor modification

This paddle switch is of good quality, it’s a great size and mounted well in the suggested Taymac SD350S box, just know it’s a little fussy aligning the switch to the box screw hole which required removing the plate ( it screws on) and running it across the grinder a few times to provide the needed clearance. The switch works well and was easy to install by following the wiring diagram shown. I’ll definitely purchase again.

Scritto da: Gabriel

Solid switch.

Had to replace the switch on my old table saw. This did the trick I made it so I could shut it off using my hip by building a small box. Changed the saw's performance. A saw that is easy to shut down and hard to start. It's exactly what I wanted. I would buy this switch again if I needed to. I would buy it again and again. It's hasn't failed me in the couple of years I owned it. <------ Yeah that is YEARS.