Foglio PEI 235mmx235mm e adesivo magnetico con adesivo per Creality Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 S1/Ender 3 S1 pro/Ender 3 neo/Ender 3 v2 neo/Ender 5/Ender 5 Pro/Voxelab Aquila Stampante 3D

Name: Foglio PEI 235mmx235mm e adesivo magnetico con adesivo per Creality Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 S1/Ender 3 S1 pro/Ender 3 neo/Ender 3 v2 neo/Ender 5/Ender 5 Pro/Voxelab Aquila Stampante 3D
Brand: UNIDO
SKU: 0783970029096
Price: 43.50 EUR
Availability: InStock

Brand:UNIDO

3.6/5

€
43.50

【Ampia applicazione】 La dimensione di Ender 3 PEI è 235 * 235 mm （9,25 * 9,25 pollici). Dopo aver installato il piano di stampa, livellarlo nuovamente per migliorare l'effetto di stampa. , è applicabile con stampanti 3D Creality come Ender-3, Ender-3 Pro, Ender-3 V2, Ender-3 S1, Ender 3 S1 pro, Ender 3 neo, Ender 3 v2 neo, Ender-5, Ender-5 Pro, CR-20, CR-20 Pro, Voxelab Aquila, Voxelab Aquila C1, Voxelab Aquila C2 e stampanti 3D FDM di dimensioni simili. Compatibile con PLA/PETG/PEEK/ABS e qualsiasi altro filamento. 【Più conveniente e pratico】 Utilizziamo PEI più spesso del 75% e acciaio per molle più spesso del 25% rispetto ai nostri principali concorrenti. Ciò significa una lastra più durevole in grado di gestire le difficili condizioni della stampa 24/7. Il nostro magnete può anche sostenere temperature più elevate di 120 °C ， Resistente all'usura e ai graffi, facile da pulire: sulla superficie del rivestimento composito è presente una pellicola protettiva, che è antigraffio e antipolvere, ecc. acciaio, polvere PEI spruzzata in superficie, giallo dorato sul retro. Flessibile, rimovibile e può aderire molto bene ai magneti. Alta resistenza e resistenza al calore. 【Facilità di rimozione】 Se utilizzato in un'applicazione di stampa 3D, PEI è eccellente perché può sopportare i numerosi cicli di calore che un letto di stampa 3D attraversa dalla stampa alla stampa. Questa superficie è facilmente rimovibile e flessibile. Le stampe si staccano facilmente dalla superficie quando la temperatura del letto riscaldato raggiunge la temperatura ambiente. Se la stampa è ancora bloccata, rimuovi la superficie magnetica superiore da quella inferiore, piega la superficie flessibile e osserva il modello cadere tra le tue mani. 【Eccellente adesione】Facile adesione alla superficie di stampa, facile rimozione delle stampe, flettersi leggermente per staccare subito la stampa. È possibile ottenere un'adesione eccellente quando la temperatura del letto riscaldato è di circa 60 ℃, foglio PEI senza utilizzare colla o altri strumenti per aiutare il modello ad aderire al foglio.

Quantity

Aggiungi al carrello Compra subito

EAN: 0783970029096

Categories: Prodotti industriali e scientifici, Prodotti di produzione additiva, Forniture per la stampa 3D, Filamento per stampa 3D,

Country of Origin	China
Item model number	PEI-1230
Manufacturer	Unido
Package Dimensions	10.87 x 10.59 x 0.83 inches; 1.12 Pounds

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Cutter

Your mileage may vary

I ordered this magnetic sheet set primarily based on the claim of it being able to withstand over 100C bed temperatures, as I planned to use it on a printer used mainly for ABS and PETG. It's on an Ender Neo converted to an Ender 3 Pro by replacing the mainboard and removing the CR-touch... I get better results manually leveling and enjoy being able to use the ENTIRE 235mm bed surface (set your bed offsets if you're missing a few mm on the left and front). The magnetism is scary strong - like it'll bite you if your finger gets in the way, and once it's down it is REALLY down. (raise the extruder up out of the way and carefully align the back edge of the PEI sheet with the bed with the front raised about 30 degrees. Once the back edge and corners are aligned, slowly lower the front until it snaps into position). I have had it to 110 degrees with absolutely no apparent reduction in magnetism. The textured surface seems rock solid - more like anodized aluminum than PEI (the Gizmodorks PEI sheet on another printer feels much softer). As to the build surface, the textured side works great, albeit leaving a bottom texture reminiscent of my blue-tape-using days, but I can't get a single thing to adhere to the smooth side. The ONE time I actually got a PLA print with a 5mm brim to stick, it actually curled up at about 6mm thickness... which I have NEVER seen PLA do. I ran the bed at 65 C to get the brim to stick, and apparently the combination of insufficient adhesion and PLA softened by the bed heat (full fan, but this sheet seems to transfer heat to the model much more readily than other surfaces I've used) made it decide to curl. The textured side works great at 60 degrees for PLA, but I got ZERO adhesion on the smooth side at that temperature. Reflecting back on my learning process over the past seven years, relatively thick (over .5mm) Kapton tape was the game changer on my Prusa clones, and I got into the habit of printing PLA on a 60C heated bed (ABS at 90-95 in a 45 degree enclosure). I like the Kapton much more than PEI, but can't find any that's more than a few mils thick. The "official Creality" build surface did nothing for me, and glass - even using the specially surfaced plate that came with the Neo, has always been an exercise in futility for me. In summation, I'm debating ordering another of these, but leaning toward a similar set with both sides of the top sheet textured, or with a double-sided textured sheet and double-sided sheet with carbon fiber stripes. If I order this again at least maybe I'll know if I got one with a bad smooth-side coating.

Scritto da: teamhex

Impressive. Big upgrade over the stock PC sheets.

I come from the days of using painters tape and Kaplan tape for adhesion on glass. Glue sticks and hairspray as well. I recently got back into printing after picking up an Ender 3 S1 and a 3 Pro. Love them and my mind was blown by the flexible PC sheets that came with them. I used the stock sheets for 2-3 months and finally I’m running into issues with them. I bought this and threw it on my S1. I can’t believe how much better this is. I mean prints pop themselves off the bed when they cool. Yet when it’s hot during printing it sticks to the sheet very well. It’s a game changer and I’m considering getting a second. I have been switching between glass and PC sheets, but if this thing holds up, I’ll probably use it going forward. I feel like my first layers are better as well. Could be my imagination, but this is quite amazing. I recommend you pick one up.

Scritto da: FAT-DAD

Sticks great

The first few prints had a problem with sticking. A corner here and a corner there wouldn’t stick. Now everything sticks, but everything comes off easily when done. I haven’t had to clean it at all. This thing is great.

Scritto da: VegasHotWheeler

Nice!

Have only done a couple of print, but I like it so far.

Scritto da: Ronnie V.

Essential 3d Printer Upgrade

If you have yet to try a PEI sheet for your 3d Printer yet, you are missing out on the ease of use and end of much frustration. This PEI has a smooth side and a textured side if you want the smoothness that you can get out of your glass sheet. I highly recommend this as an essential printer upgrade, you will not regret it, and no more scraping and fudging to get your prints off the bed. This installs in seconds, and only requires a quick relevel. One bonus of this sheet is the dual tabs making it easy to lift off from either side of the bed. Again highly recommend this for your Ender3v2 not sure why I waiting so long.

Scritto da: spadic

Works great!

Had to cut slots for my exposed screws on my 5 S1 bed but it is the correct size. Couldn’t find just the metal plate! My 5 S1 already has a magnetic base.

Scritto da: Shane

Product works great, prints stick during the print and come off easily when cooled

The will fit multiple printers as long as the bed size is 235x235. I tested on a Fookos Odin F5 and it fit perfect. Reversable, with both textured and smooth. I was a bit worried about the smooth side as it doesn't appear to have a PEI sheet, unless it's incredibly thin. However after printing on it, it works great I was surprised how well the print stuck to the smooth side of the bed, with the bed still warm I had to use a bit of force to remove the print, which says to me it wasn't going anywhere. Personal preference for most on the smooth vs textured. Personally either one works for me, both side worked well, and function as expected. I did include a picture to show the texture vs smooth bottom finish The included magnet sheet is very strong, grabs the print surface very firmly.

Scritto da: Killerdave

Works great and at good price.

I love this sheet it sticks very well. It's better then the glass I had.