Sigillante per perdite per barche in alluminio TotalBoat

Name: Sigillante per perdite per barche in alluminio TotalBoat
Brand: TotalBoat
SKU: 0811932022776
Price: 72.34 EUR
Availability: InStock

Brand:TotalBoat

3.3/5

€
72.34

Le barche in alluminio conducono una vita dura. Si arenano, colpiscono le cose immerse nell'acqua e tendono ad essere utilizzate per molti anni. Nel corso del tempo, rivetti e cuciture sviluppano perdite, crepe o addirittura fori. Una barca di alluminio che perde può affondare rapidamente. La maggior parte dei prodotti di riparazione esistenti sono noiosi e richiedono tempo. Le loro istruzioni richiedono di rivestire la parte inferiore della barca. Non gestiscono bene la flessione o lo stress, il che porta a crepe e guasti della riparazione. Il sigillante per perdite per barche in alluminio TotalBoat è diverso. È il modo semplice e veloce per riparare rivetti che perdono, crepe, cuciture e buchi nella tua barca in alluminio. Viene fornito in una pratica cartuccia che si inserisce in una pistola per calafataggio standard. Basta inserire la cartuccia nella pistola, collegare la punta di miscelazione inclusa alla cartuccia, puntare, tirare la maniglia e scartare i primi 3-4 pollici di tallone. Successivamente, il sigillante per perdite esce miscelato con l'esatto rapporto 1: 1 in modo da ottenere una cura adeguata e un sigillo impermeabile. È così semplice ottenere la giusta miscela e una cura affidabile ogni volta Se vivi in un clima più freddo, apprezzerai il fatto che non devi aspettare che il clima si riscaldi: puoi applicare Aluminium Boat Leak Sealer quando la superficie in alluminio e la temperatura dell'aria ambiente sono inferiori a 40 ° F, purché la superficie in alluminio sia stata preparata correttamente. Il sigillante per perdite in alluminio per barche è resistente all'abbassamento, quindi rimane dove lo metti e non gocciola da cuciture e fori. Il tempo di gel è di 40 minuti a 22 °C. La resistenza alla flessione è di 8.800 psi. La resistenza alla compressione è di 7.200 psi. Dipingi su riparazioni indurite per la massima protezione. Attendere 7-10 ore prima di carteggiare e verniciare. Attendere 24 ore prima di sottoporre la resina epossidica indurita a carichi elevati. Confronta con il kit di riparazione per barche in alluminio West System G/Flex 650-K. Con TotalBoat, non c'è misurazione, nessuna miscelazione, nessun disordine e quasi nessuna pulizia. Tutti i prodotti TotalBoat sono sviluppati da diportisti per diportisti, per offrire grande valore e grandi risultati. Sappiamo cosa funziona e cosa no.

Quantity

Aggiungi al carrello Compra subito

EAN: 0811932022776

Categories: Sport e tempo libero, Prodotti industriali e scientifici, Sport e forma fisica, Canottaggio e vela, Barche e attrezzature, Forniture per la manutenzione, Forniture per la pittura,

Disponibile nel pratico formato da 250 ml. cartuccia che si adatta comodamente alle pistole per calafataggio standard. Include 2 punte di miscelazione statiche. Resina e indurente vengono forniti in un'unica cartuccia e vengono erogati automaticamente nel rapporto corretto. Nessuna miscelazione. Nessun disordine da pulire. Può essere applicato su superfici in alluminio opportunamente preparate quando la temperatura dell'aria e del substrato è inferiore a 40°F. Il lungo tempo di lavoro (75 minuti @ 72°F) garantisce una migliore penetrazione e una migliore tenuta. Assorbe le sollecitazioni da contrazione, vibrazioni, urti ed espansione tenendo saldamente per evitare perdite. Il sigillante epossidico impermeabile in due parti, facile da usare, ripara rivetti e giunture che perdono e rattoppa piccoli fori su barche in alluminio in modo rapido ed efficace.

Brand	TotalBoat
Color	Buff
Compatible Material	Aluminum
Is Discontinued By Manufacturer	No
Item model number	497724
Manufacturer	TotalBoat
Material	Resin
Package Dimensions	9.92 x 2.87 x 1.93 inches; 13.76 Ounces
Style	Compact

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Kindle Customer

Easier to apply than other ratings implied

I bought this product to seal loose rivet leaks in my aluminum boat. I have not put the boat on the water yet, so cannot comment on how well it worked. That's why I gave it four stars and not five. I gave it four because the product was delivered promptly including a card asking for comments and offering a 20% coupon for future purchase as well as a product support phone number. Very nice service offer that at least appears as if the company - TotalBoat - is concerned about customer satisfaction. The product came well packaged and included two dispenser tips and a container that fits any caulk gun. Other comment had me a bit worried about being able to dispense the epoxy because I don't have great hand strength, however, cautioned by instructions on the tube I laid it in front of a heat duct while I prepared the surface and then had no trouble dispensing it at all. It was easy to get out of the tube, emerged as a not overly thick and easily pliable liquid that was very easy to manipulate, and ultimately made a nice layer that looks like a good seal. I applied it to rivets in the boat's floor then again on the bottom (so overhead). It stuck and stayed well in both locations. I've used Gluvit before and been very happy with it's property of filling in along the shaft of rivets as well as over the ends. This product is a little thicker, but it also had some flow so I'm hoping, but can't say for sure, that it did the same. In a week or two after I've finished this repair and installed the new floor, I will put the boat and the water. If it works as I hope, I'll change the rating to five stars. If not - well, you may see a new message in this space, but from all appearances I expect it to perform well.

Scritto da: Amazon Customer

Not mixing

I’m sealing the rivets on an aluminum Jon boat, the package states first 3-4 inches will be waste until mixed. I wasted first 5” just to be sure. For the next 40 rivets it seemed to work fine, then half way through it changed colors and I was only getting the orange/brown color assuming this is just hardener. So half my boat rivets got the epoxy side and the other half got just the hardener. Not happy with how it turned out because the first half I had to wipe off because there was no hardener. In the future I would buy a pre mixed boat epoxy from Home Depot.

Scritto da: Amazon Customer

Great product

I used this to seal some leaky rivets on a jon boat I recently acquired. Using a cheap caulk gun and the provided tips, it worked very well. It can be a little temperature sensitive so make sure you apply in conditions above 60 degrees. I did some application at that temperature and really killed my hand trying to squeeze the caulk gun trigger. I finished the job a few days later in warmer weather and found the application to be so much easier. The only thing to be aware of is that the tube can be a little misleading in size. It's only about 1/2 full, but I was able to seal every rivet on the bottom of my 14 boat, half the rivets on the inside, and several of the seams. It is however a caramel colored product and won't dry clear, so it will stand out that you've used it. That being said, it was perfect for my needs.

Scritto da: Real Customer

It seems to work

It takes more than 3 inches of material before it is properly mixed. Wait for the color to change to brown before applying it. It was white after 4 inches so I used it as it changed color. That section did not harden.

Scritto da: Jonathan Cowal

So far this has been a great product. I used it to seal every rivet ...

So far this has been a great product. I used it to seal every rivet and seam on an aluminum boat I was fixing. Some people have complained that it was difficult to dispense but I purchased the cheapest caulk gun I could find and it wasn't too bad. It was very easy to work with, I used a putty knife and was able to shape it easily around the areas I was working on. Also, it really does stay exactly where you apply it even when working on slanted or even upside down surfaces. Once sanded, I was able to paint over it and you cannot tell that there is anything there. I give it 4 stars because I have yet to test the boat out and I do not know how it holds up over time.

Scritto da: Kevin Vail

Very easy to use

I bought this to pro-actively seal the non-welded ribs on the hull of my 14ft v-hull. The mixing tip worked great. Each stick comes with two mixing tips in case you don’t use all of the compound in one instance. The compound is very easy to work with and apply and dries pretty quick for sanding and painting. So far I would highly recommend any product from this company.

Scritto da: MattG

Sealed up leaky aluminum boat

Worked well. I used it to seal a leaky riveted seam where the bottom of my aluminum boat meets the transom. Followed the instructions regarding surface prep, no problem squeezing it out with a standard cheapie caulking gun. Came out thin enough for me to force it into and through the seam with some compressed air, then gave it a thicker bead inside and out, then had plenty of time to smooth it. Took paint well. The following week, took it out to the lake, it sat in the water for 6 days with an hour or so of driving around each day, and no leaks at all. Very satisfied.

Scritto da: Barbara Bing

Takes some experience to apply

Did a good Job on leaks to an aluminum boat. Stuff is quite viscous and ease of application depends on size of opening. Used calking gun. Two nozzles to try with - you get better with time.