RIDGID 32870 Tagliatubi a 4 ruote per impieghi gravosi modello 42-A, tagliatubi in acciaio da 3/4" a 2", argento/rosso, piccolo piccolo argento/rosso

Brand:RIDGID

3.2/5

€
374.28

RIDGID copre i propri prodotti con una garanzia a vita contro difetti di materiale o lavorazione per l'intera durata dell'utensile. Il tagliatubi ha una capacità del tubo da 3/4 di pollice (20 mm) a 2 pollici (50 mm). Dotato di 4 ruote per carichi pesanti. Dispone di una maniglia corta per un uso più semplice in aree ristrette. Progettato per lavorare in aree in cui è impossibile una svolta completa.

Prodotto non disponibile

EAN: 0095691328700

Categories: Strumenti e miglioramento della casa, Utensili elettrici e manuali, Utensili manuali, Taglierine, Tagliatubi,

Batteries Included?	‎No
Batteries Required?	‎No
Certification	‎certified frustration-free
Color	‎Silver/Red
Customer Reviews	4.1 4.1 out of 5 stars 40 ratings 4.1 out of 5 stars
Is Discontinued By Manufacturer	‎No
Item model number	‎32870
Item Package Quantity	‎1
Item Weight	‎7.33 pounds
Manufacturer	‎Ridgid Tool Company
Part Number	‎32870
Product Dimensions	‎3.2 x 7.8 x 18.6 inches
Size	‎Small
Warranty Description	‎Ridgid covers its products with a lifetime warranty against defects in material or workmanship for the life of the tool

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Dave P.

Works better as a 2 wheel cutter

I grew up in a Mom & Pop & Sons plumbing business and was cutting and threading pipe long before I could drive a car--and Dad had the wisdom to use mostly RIDGID tools, which he never had to swear at or throw to get them to work properly. But I considered returning this cutter because I also found it hard to keep the 4 wheels on track when starting a cut. Instead, I decided to replace the 2 cutters on the tool body with rollers so that the 2 moveable cutters did all the cutting--and the rollers would hold it on track due to the much greater contact with the pipe. But RIDGID rollers were difficult to find or way too expensive, so my MacGyver idea was to substitute steel flat washers for rollers. Any hardware store will have flat washers that are 1" diameter with a 3/8" hole. Stack 10 into each cutter slot--they'll be a little loose since the pin is 5/16" diameter. The washers will turn freely and keep the cutting wheels tight to the pipe and in perfect alignment. I'm cutting chain link line posts and top rails, and the cuts made with the washer-rollers are perfectly perpendicular to the pipe and started straight on the first turn. I do have one post close to a tree, so I'll need to start the cut using the washers and 2 cutters, then install all 4 cutters to cut the entire circumference of the pipe--but a minor inconvenience since the pins tap out with a small hammer and pin punch or Phillips screwdriver, so that it takes just a few minutes to swap cutters and washer stacks. So, do I get a RIDGID TOOL calendar for this great review?

Scritto da: Mike

nice heavy duty cutter

well built Large Cutter

Scritto da: Josedude

Ridged 32870 model 42-A worked very well for me

I used this to make 3 cuts in 1 1/2 inch cast iron drain pipe. It worked very well for me. I could not rotate the cutter far enough to get a full cut all the way around the pipe, but the pipe still broke very cleanly, especially considering the poor condition of the pipe. While I only made 3 cuts, I imagine it should last for many more cuts. The T handle was very easy to turn, and the length was sufficient to rotate the cutter around the pipe after tightening. I had purchased two sets of replacement cast iron cutting disks, but the ‘stock’ cutting disks that came on the cutter worked just fine.

Scritto da: Ev

Does not work as advertised

Top and bottom cutting wheels do not line up. Returned to seller. Contacted them about when refund would be issued 2 weeks ago they have still not responded.

Scritto da: James W.

Cutter walk too much

Cutters walk too much

Scritto da: Tom

Good tool

Good Tool!. Very well built and heavy duty. Very quicky action. However, at the beginning it's difficult to follow a guide and get a square cut. If you plan to thread, you must have a lot a patience with a file to eliminate the external ridge

Scritto da: thefotog

They work perfectly in tight spaces

They have saved my tail quite a bit lately. Great for tight spaces but they do leave the ends a bit flaired, Mean that there is a bit of filing to do before threading.

Scritto da: Amazon Customer

Good Product

Satisfied

Scritto da: dave

articolo difettoso

il taglio della parte inferiore del tubo non corrisponde a quello della parte superiore( i 2 tagli nn coincidono) articolo ono utilizzabile

Scritto da: LUCA

Ottima

Ottima tagliatubi, perfetta anche per uso intenso.