Rain Bird TP25-30PK Tubo di irrigazione a goccia con chiusura terminale, tappo "Goof" per tubo da 1/2", confezione da 30 tappo/chiusura terminale confezione da 30

Brand:Rain Bird

3.7/5

€
24.43

DESCRIZIONE PRODOTTO Rain Bird TP25-30PK Goof Plug per tubi di irrigazione a goccia, confezione da 30. Il tappo di plastica nero, noto anche come "tappo goof", sigilla i fori indesiderati in tutte le marche di tubi di irrigazione a goccia da 1/2 o più grandi. Utilizzare anche per terminare tratti di tubi gocciolanti da 1/4”; si adatta a tutte le marche di tubi da 1/4”. Facile da inserire a mano o utilizzare lo strumento Rain Bird ET/1PK25S (venduto separatamente) per un'installazione rapida e semplice o progetti più grandi. Basta inserire il tappo del tubo nel grande foro situato all'estremità dell'utensile e spingerlo nel foro indesiderato per una tenuta sicura a prova di perdite. La spina presenta piccole creste progettate per tenerla saldamente nello strumento; si appiattiscono leggermente quando viene inserito il tappo, consentendo un facile dispiegamento nel tubo e la rimozione dell'utensile. Costruito con materiali resistenti ai raggi UV e agli agenti chimici altamente durevoli per garantire una lunga durata. Confezione da 30 tappi in un pratico sacchetto di plastica. Rain Bird "L'uso intelligente dell'acqua". DAL PRODUTTORE Rain Bird Corporation è una società privata fondata nel 1933 durante il boom agricolo in California. Siamo riconosciuti come il produttore e fornitore n. 1 al mondo di prodotti e servizi per l'irrigazione. Con uffici vendite in tutto il mondo; offriamo oltre 4.000 prodotti per l'irrigazione a risparmio idrico in più di 130 paesi. Sin dall'inizio, Rain Bird ha prodotto e offerto la più ampia gamma del settore di prodotti per l'irrigazione di alta qualità per: fattorie, campi da golf, arene sportive, complessi commerciali e abitazioni. Negli ultimi 80 anni Rain Bird ha ricevuto più di 450 brevetti in tutto il mondo. Compreso il primo per l'irrigazione nel 1935 per il nostro originale irrigatore a percussione (brevetto USA n. 1.997.901) che ha rivoluzionato la produzione alimentare agricola e ha inaugurato una nuova era nell'irrigazione in tutto il mondo. Nel 1990 questo irrigatore a impatto originale è stato designato come punto di riferimento storico dall'American Society of Agricultural Engineers. I nostri prodotti coprono tutti gli aspetti dell'irrigazione... timer/regolatori, irrigatori rotanti pop-up, irrigatori a testa di spruzzo pop-up, ugelli per irrigatori, valvole di irrigazione, irrigazione a goccia, drenaggio e molto altro. Questi prodotti sono stati tutti scelti e installati in tutto il mondo nei più grandi e prestigiosi progetti per l'irrigazione residenziale, commerciale, agricola e dei campi da golf. Rain Bird è impegnata in The Intelligent Use of Water™ con il nostro impegno che si estende oltre i prodotti all'istruzione, formazione e servizi per l'industria e la comunità. La nostra eredità è progettare e produrre solo prodotti di altissimo valore e qualità. Siamo grati di aver ricevuto numerosi premi di riconoscimento da molti dei nostri stimati partner. Rain Bird “L'uso intelligente dell'acqua

Quantity

Aggiungi al carrello Compra subito

EAN: 0077985007027

Categories: Patio, prato e giardino, Giardinaggio e cura del prato, Attrezzature per l'irrigazione, Attrezzatura per l'irrigazione automatica, Tubo di irrigazione,

Confezione da 30 tappi in un pratico sacchetto di plastica. Costruito con materiali resistenti ai raggi UV e agli agenti chimici altamente durevoli per garantire una lunga durata. Plastica nera resistente. Progettato per funzionare con lo strumento emettitore Rain Bird ET/1PK25S (venduto separatamente). Utilizzare come chiusura terminale per terminare 1/4 di tubi. Tappi fori indesiderati in tutte le dimensioni di tubi 1/2 gocciolamento.

Brand	Rain Bird
Color	Black
Connector Type	Plug
Country of Origin	USA
Customer Reviews	4.6 4.6 out of 5 stars 2,460 ratings 4.6 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Brass
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	1.57 x 1.25 x 8.38 inches
Item model number	TP25-30PK
Item Weight	0.04 Pounds
Item Weight	0.662 ounces
Manufacturer	Rain Bird
Material	Plastic
Number of Pieces	30
Product Dimensions	1.57 x 1.25 x 8.38 inches
Size	30-Pack

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Lee

Cheap quality

Typical cheap made but seems to do the job

Scritto da: Sabrina Lok

Works fine with no work leak

Works as expected. No leak at all

Scritto da: Sj773

Great Irrigation Distribution Tube Coupling

We bought & used 2 packs of these fittings for 2 separate projects: To irrigate our raise garden beds and to set-up a system for our hedge of Podocarpus bushes at the yard's perimeter. This allowed us to go on vacation without any worries about our plants. These couplings fit easily into the hole with a tight seal (just take care to punch the holes at a right angle to the tubing so the hole isn't distorted). I also used a few couplings from another irrigation kit I had but I wouldn't say I had a preference between one style of the other. (See pics) Here is what we used for our irrigation systems: (Qty 1) TimerOrbit 3-Outlet Programmable Hose Faucet Timer (Qty 2) 50-Pack Drip emittersAxe Sickle (Pack of 50) Drip Emitters Perfect for 4mm/7mm Tube, Adjustable 360 Degree Water Flow Drip Irrigation System for flower beds, vegetable gardens, herbs gardens. (Qty 4) 100' Irrigation tubing 1/4''Gunsamg 1/4'' Blank Distribution Tubing Drip Irrigation Hose (100foot) ,KORAM Drip Irrigation 1/4 Blank Distribution Tubing Drip Watering Hose 100ft Roll with Plant Garden Labels (Qty 2) 30-Pack 1/4" Coupling fittingRain Bird BC25-30PS Drip Irrigation Universal 1/4" Barbed Coupling Fitting, Fits All Sizes of 1/4" Drip Tubing, 30-Pack (Qty 2) Hose end plugsRaindrip 304G00UB 5/8-Inch Hose End Plug with 3/4-Inch Cap, Loose (Qty 1) Soil / moisture / pH testerSoil Tester, Deepow 3-in-1 Soil Moisture Meter, Soil Ph Meter Kit for Moisture, Light & pH - Helpful for Garden, Lawn, Indoor & Outdoor, High Accurate & Easy Read Indicator (No Battery needed) TIPS on How to Set Up Your System: - To make the distribution tubing MUCH easier to work with, just soak it in warm to hot water or lay it out in the sun for a little while to soften. - Always a good idea to flush the system a bit before installing emitters to clear any debris. - Create your lateral lines (1/4-in. tubing and emitters) BEFORE hooking them up to the main line. - ALWAYS cut the tubing LONGER than needed! Much easier to trim off excess than to try to come up with additional lengths of tubing if mis-cut too short! - Be sure to hold the hole punch at a right angle to the tubing when you punch a hole and you'll get a perfect seal around the barb of the coupling. - Place the emitter stakes strategically so that the plant's root ball will be kept damp but not soaked. - Adjust the flow for each plant and again every season according to the plant size. TIP: Remember to reaccess requirements as they grow and needs change! - Your emitters farthest from the faucet will need to be set on a freely flowing adjustment due to loss of water pressure. - Use a timer to water twice a day for only 5 or 10 minutes, depending on the plant's needs and weather. - Test to make sure the moisture is getting where you want it. TIP: Don't assume rain means you can turn off the irrigation system. Leaves can redirect rainwater so it doesn't actually reach the roots! - We didn't add a fertilizer injector to the faucet assembly this time, but we might try this step next year so we can feed our plants while we water. TIP: Don't forget to Install a good filter and change it every few months or at least once a season, especially if you have alkaline, mineral-rich, or well water. Why do you need an automatic drip irrigation system for your container or raised garden? Simple. Containers dry out so quickly that they often require once or even twice daily watering in hot weather. So just bite the bullet and do it. These couplings worked perfectly for our irrigation systems in our veggie garden as well as for the perimeter hedge, so now I don't have to lug around hoses to water them each day. A real time-saver that we should have done long ago. Recommended & will buy again!

Scritto da: Judester 48

Great for monitoring water flow.

These are the best for monitoring the water flow of my potted plants. The line isn't separate from the main watering area and without these the plants get too much water and waste it.

Scritto da: Richard K.

Works

Works As expected

Scritto da: Bàká Hään

Very useful

We bought a new house and the backyard sprinkler system was broken beyond repair. Even with professional help, I was unable to locate the sprinkler valves for the back yard. So instead I set out to research and install my own drip irrigation to automate the watering process, mostly because I am way too lazy to water my backyard every other day. I chose the rainbird family of products because of the positive reviews and the plethora of options. I chose drip emitters for the trees and shrubs in my yard. I chose 1/2 in tubing for the systems backbone. Then 1/4 in tubing to run out to the individual plants, flowers, trees, shrubs... There are two ways you can install them. You can install them straight into the 1/2 in tubing, like I did. The other way is to install a 1/4 in coupler into the 1/2 in tubing, then run a 1/4 tube to the plant. Then connect the drip emitter at that end. I chose this configuration because some people complain about the water pressure pushing the emitter off the end of the tubing. I bought this took in order to connect the 1/2 in tubing with the Tee and elbow fittings. These plugs have two uses. If you make a mistake and punch a hole in the 1/2 in tubing that you don't want (goof) then you can use these plugs to close that hole. You can also use them to plug the end of the 1/4 in tubing. I did that for the tubing that I ran for future expansion, but I am not using yet. + Good price. + Very easy to use. I do recommend using the emitter insertion special tool to insert these goof plugs. I personally dislike special tools, but they are only a couple bucks each. I saved a ton of money by doing this project myself ($250 total cost), so to me it was worth it to get this specialized tool. + Very happy with the performance so far. - Nothing thus far. I am very happy with the performance of these plugs Ill update this review as necessary.

Scritto da: Bàká Hään

Good coupling fittings

We bought a new house and the backyard sprinkler system was broken beyond repair. Even with professional help, I was unable to locate the sprinkler valves for the back yard. So instead I set out to research and install my own drip irrigation to automate the watering process, mostly because I am way too lazy to water my backyard every other day. I chose the rainbird family of products because of the positive reviews and the plethora of options. I chose drip emitters for the trees and shrubs in my yard. I chose 1/2 in tubing for the systems backbone. Then 1/4 in tubing to run out to the individual plants, flowers, trees, shrubs... There are two ways you can install them. You can install them straight into the 1/2 in tubing, like I did. The other way is to install a 1/4 in coupler into the 1/2 in tubing, then run a 1/4 tube to the plant. Then connect the drip emitter at that end. I chose this configuration because some people complain about the water pressure pushing the emitter off the end of the tubing. I bought these coupling fittings to connect the 1/4 in tubing to the 1/2 in tubing for future expansion. Then I put goof plugs into the ends of the lines I am not using yet. + Good price. + Very easy to use. I recommend using the Rainbird special tool to insert the barbed end into the hole you punched into the 1/2 in tubing. I personally dislike special tools, but they are only a couple bucks each. I saved a ton of money by doing this project myself ($250 total cost), so to me it was worth it to get this specialized tool. + Very happy with the performance so far. - Nothing thus far. I am very happy with the performance of these coupling fittings. Ill update this review as necessary.

Scritto da: Geoffrey Gaucher

Way better than Orbit brand!

Excellent quality item, and the best brand I have found to use.

Scritto da: Linda Martin

Great Product

Great product thank you.

Scritto da: Charles Bongiorno

Five Stars

Works perfectly.

Scritto da: Dofand

Keeps the tubing locked in place

This tubing stake is superior to the original stake as you can lock the tube onto the stake where the other allows the tube to slip out under the slightest pressure. The bug cap works great when the dripper is connected directly to the main line.

Scritto da: Rick Benjamin

2 items for this price is outrageous.

Returned for poor delivery from Purolator. Price is outrageous.