0
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister

Gardner Bender HST-WP Kit di giunzione per tubi per pozzi 14-8 AWG Kit di giunzione di testa

Brand:Gardner Bender

3.6/5

€
27.78

Il kit include il connettore di giunzione a vite e 4 tubi termoretraibili in poliolefina a parete pesante con rivestimento adesivo a tenuta stagna. Per l'interramento sottomarino di cavi per pozzi da 8 a 14 AWG. Per la riparazione impermeabile del filo del pozzo. Il kit include il connettore di giunzione a vite e 4 tubi termoretraibili in poliolefina a parete pesante con rivestimento adesivo a tenuta stagna. Per l'interramento sottomarino di cavi per pozzi da 8 a 14 AWG. Per la riparazione impermeabile del filo del pozzo. Il prodotto è fabbricato in Cina. Kit di facile e semplice utilizzo. Il prodotto è un buon kit di giunzione della pompa.

Quantity
Aggiungi al carrelloCompra subito

EAN: 0032076893736

Categories: Prodotti industriali e scientifici, Elettrico industriale, Cablaggio e connessione, Guaina termorestringente,

Il kit include il connettore di giunzione a vite e 4 tubi termoretraibili in poliolefina a parete pesante con rivestimento adesivo a tenuta stagna. Per l'interramento sottomarino di cavi per pozzi da 8 a 14 AWG. Per la riparazione impermeabile del filo del pozzo. Il kit include il connettore di giunzione a vite e 4 tubi termoretraibili in poliolefina a parete pesante con rivestimento adesivo a tenuta stagna. Per l'interramento sottomarino di cavi per pozzi da 8 a 14 AWG. Per la riparazione impermeabile del filo del pozzo. Il prodotto è fabbricato in Cina. Kit di facile e semplice utilizzo. Il prodotto è un buon kit di giunzione della pompa.
Brand Gardner Bender
Certification UL
Insulation Material Polyolefin
Material Plastic
Terminal Screw Terminal

3.6

13 Review
5 Star
74
4 Star
15
3 Star
6
2 Star
2
1 Star
3

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: D. A. Soss
#2 AWG Will Not Work
Tried this with #2 AWG solid tinned copper wire. The wire slipped in easily enough, but the setscrews. would not engage.
Scritto da: JessieQ
Takes a long time to shrink
Overall good quality product! My only quibble is that the tubing takes very long time to shrink, although I carefully followed the instructions and use a heat gun with the recommended temperature setting.
Scritto da: Sam Smith
Worked well for trolling motor connections
Used these to attach a plug with 6AWG wire to a trolling motor. The connectors worked well and definitely sealed well once the heat shrink fully shrunk down. It will take a good heat source to shrink this heat shrink, it is heavy duty. I believe I had my gun to 800F to make good progress on the shrinking process. I have no concerns about the connection being water tight now.
Scritto da: frank c hanzal
size matters
easy and securely fasten
Scritto da: R. Hardage
Not easy for 2 awg wire.
Worked great for 6 awg wire. Not so easy with 2 awg wire. The wire barely fits in hole for 2 awg and it is hard for the set screw to catch a thread when tightening.
Scritto da: Surrealone
Solid splice kit -- no issues with heat shrink tubing, here...
I'm not sure what others are complaining about when it comes to the heat shrink tubing. Perhaps they've just not worked with heat shrink tubing much? I ordered three of these to do code-compliant splices of a 10/3 run, a 14/3 run, and a 14/2 run ... all of which exceeded 250 feet and, thus, needed to be spliced in order to use standard cable rolls instead of purchasing it by the foot. I took my time and was in no hurry with the splices. I elected to do the 10/3 run first since it would need the least shrinkage on the tubing and I could take my time to gauge how much heat could be applied safely. This stuff begins to shrink around 200F, but you must heat a fair amount of it to get it to begin to shrink. I used an electric heat gun with temperature control on it and found that by setting the gun at 600F and holding the nozzle approximately 1.5" from the tubing and fanning it back/forth along the tubing in 3-4" wide strokes, I could get it to shrink fairly readily. I heated 1/4 side of the outside of the tubing cylinder ... starting in the center and working outward to the ends. Once that quarter section had shrunk, I did the next quarter section ... then the third quarter section, then the fourth -- each time working from the center of the tubing, outward. I shrunk it in stages, too ... meaning I didn't try to get maximum shrinkage in each quarter; instead, I shrunk it a bit at a time for all four quarters of the cylinder ... and then re-shrunk it again. I did this to promote even-ness in shrinkage along all quarters ... to avoid holes or weak spots in the tubing. Since I was being careful and trying to find the correct temperature to use with my gun on this tubing, the first use of the heat gun took ~10 mins ... on the largest of my wires. However, once I had a known good temperature, I was able to shrink the others in ~3 minutes after putting the splice hardware in place. I had no issue with the 14/3 or the 14/2. The tubing shrunk enough for it. Key to this was the adhesive inside of it, which melts. I made sure to wear insulated leather gloves during the heating process so that as I was finishing up the shrinking of the tubing I could squeeze it together and feel the adhesive flow and set -- making sure there were no open air pockets or bubbles in the adhesive (that could result in easy puncture points later, during or after burial). These kits served me well and I will buy/use them again if I need to make code-compliant underground splices in the future.
Scritto da: VH
It works
Easy to use
Scritto da: TheWhiteBasicB...
Perfect for my car, doesn’t limit amps much
I had to splice two 4 gauge wires together for the main fuse board in my car and many products just limited the amps too much and caused issues but this one worked great!
Scritto da: J-P
Kit d'épissure
J'ai réuni deux câbles d'appoints de 10 pieds pour en faire un de 20 pieds c'est une réussite. Étanche et solide, isolé pour ne pas faire un court-circuit
Scritto da: G. Laporte
Excellent produit
J’ai réparé mon câble électrique sous terrain avec ce kit. Bonne qualité. J’ai chauffé le shrink tube avec un lighter et il y avait une sorte de colle à l’intérieur du tube pour rendre la réparation étanche.
Scritto da: david bourre
Très bon kit de jonction.
Très bon kit pour faire les jonctions souterraines. Le "shrink" contient de la colle à l'intérieur qui vient tout sceller comme il faut.
Scritto da: Phil Parent
A1
Just what the doctor ordered
Scritto da: Tania and Illya
Worked as described
Worked great

Prodotti correlati

hot
Gardner Bender HST-WP Kit di giunzione per tubi per pozzi 14-8 AWG Kit di giunzione di testa
3.6/5

€ 27.78

Gardner Bender HST-WP Kit di giunzione per tubi per pozzi 14-8 AWG Kit di giunzione di testa
3.6/5

€ 27.78

hot
Grafix KSF6-WIJ Film termoretraibile stampabile 8.5X11 6PC, 6-Pack, Bianco, 6 Count White 6-Pack
3.6/5

€ 38.40

Grafix KSF6-WIJ Film termoretraibile stampabile 8.5X11 6PC, 6-Pack, Bianco, 6 Count White 6-Pack
3.6/5

€ 38.40

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart

Totale:€ 0.00

Vedi carrelloCheckout

Categorie

Tutte le categorie
Menu Categorie Cerca Carrello

Menu