Dado flangiato esagonale in acciaio inossidabile 18-8, flangia seghettata autobloccante con finitura liscia, filettatura ASME B18.2.2, 5/16"-18 (confezione da 25) 5/16"-18 1 1/4 pollici 9/32 pollici 0 Pollici 0 Pollici 25

Brand:Small Parts

3.7/5

€
27.14

Soddisfa le specifiche ASME B18.2.2. La superficie liscia non ha finitura o rivestimento. L'acciaio inossidabile 18-8 offre una buona resistenza alla corrosione e resistenza. La flangia seghettata autobloccante scava nel materiale da fissare per aiutare a prevenire l'allentamento. La base flangiata elimina la necessità di una rondella durante il fissaggio dei componenti e il corpo esagonale si serra lateralmente con una chiave, consentendo l'uso quando lo spazio sopra il dado è limitato.

Quantity

Aggiungi al carrello Compra subito

EAN:

Categories: Prodotti industriali e scientifici, Chiodi, viti e elementi di fissaggio, Noccioline, Dadi flangiati,

Exterior Finish	Stainless Steel
Fastener Type	Flange
Material	Stainless Steel
Metal Type	Stainless Steel
Thread Size	5/16"-18

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Kennaldo

They’re nuts

The nuts are great. Amazon, however, keeps sending me packs of 10 when I ordered 25. They let me keep the first pack of ten. They wanted the second 10 pack back. Curious to see if the third time is a charm. Third time was a charm, they finally sent me a pack of 25. I’m a happy camper.

Scritto da: Sharon Marchand

Easy fix

A hard to get piece of hardware that was needed to repair an expensive carriage wheel.

Scritto da: pat

Received package of 10- not 25:

Nuts arrived on time , however package o package of10-not 25.

Scritto da: phillip taylor

Good value

What can you say about nuts? All have good threads and fit the studs on our Polaris Sportsman 500. Better than buying from the dealer

Scritto da: Amazon Customer

Repurposed

Maybe I shouldn't write a review, as I did not use these as nuts. So, I can't say anything useful about the threads and such. However, I did use these as mixing weights in my (ceramics) slip container, and they work perfectly. The flanges cut through the lumps of clay as I shake the container. I can use 3 in 12 ounces of water/clay, and within a minute of shaking, have a really nice container of smoothly mixed slip. Since they're nice and heavy, they go to the bottom, out of the way. The finish on the nuts looks good, and has lasted very well - no rust or flaking.

Scritto da: Douglas H.

I never ever overspend

hi there , I just received these nuts and they look great and I was able to tighten up my trailer running board . with out any problems from these nuts . a really great value that should work as needed for a long time

Scritto da: Aleks M

Bolt threads eat into the nuts and seize them

Had the unfortunate joy of trying to remove these nuts. 1 in 5 nuts ended up cross threading when tightening using just a 1/4" hand ratchet. Then they wouldn't come off until I heated them with a torch and snapped them off with the bolts. Something was not right with the nuts I received. Thread pitch and everything was correct. The temper or something must be off since the bolt thread just bit right into the nuts when tightening.

Scritto da: Old Geezer

Non-rusting With Built In Washer and Locking Serrations--HIGHLY RECOMMENDED!

These nuts have a flanged base so you don't need a flat washer, plus they have serrations on the underside that help keep them from loosening. These are especially helpful when using carriage bolts where a nylock type lock nut may cause the bolt to spin, and would essentially be impossible to remove from an aged board.