Crimpatrice ad impatto elettrico Malco C5A2

Name: Crimpatrice ad impatto elettrico Malco C5A2
Brand: Malco
SKU: 0686046547091
Price: 221.41 EUR
Availability: InStock

Brand:Malco

3.4/5

€
221.41

Il Malco turbo crimper impact è un accessorio semplice e compatto che funziona esclusivamente con l'ausilio della tecnologia Impact Driver per crimpare in modo sicuro ed efficiente tubi rotondi zincati da 30 a 24 gauge (da 0,41 a O,71 mm) e tubi neri (da 0,31 a 0,61 mm) neri tubo della stufa. L'impatto del crimper turbo non richiede installazione o regolazione. Basta inserire l'albero di trasmissione della scanalatura di alimentazione da 1/4 di pollice al driver ad impatto cordless o con cavo (min.12 volt CC / max. 7 amp CA) per iniziare immediatamente a crimpare più dimensioni, tipi e spessori di tubi e condotti, incluso condotto a spirale, veloce e facile. Con la giunzione del tubo o del condotto in posizione chiusa, avviare la crimpatura su un lato della giunzione tirando delicatamente il grilletto del driver e inclinando l'impatto del turbo crimper sul bordo metallico. Spostare la piegatrice attorno alla circonferenza del tubo in modo controllato e quindi inclinare la piegatrice dal metallo mentre la piegatrice si avvicina all'altro lato della giunzione. L'impatto della crimpatrice turbo è cinque volte più veloce di uno strumento di crimpatura manuale basato su prove sul campo effettive! è comodo da manovrare per qualsiasi operatore e, i mancini prendono nota, funziona con il conducente dell'impatto in avanti o indietro. Il pratico piccolo turbo crimper impact è un accessorio indispensabile per ogni installatore HVAC e si ripone facilmente in una borsa o borsa per attrezzi pronta quando non viene utilizzato.

Quantity

Aggiungi al carrello Compra subito

EAN: 0686046547091

Categories: Strumenti e miglioramento della casa, Utensili elettrici e manuali, Utensili manuali, Crimpatrici per fili,

Negozi in custodia o borsa. Compatto, facile da manovrare e bilanciare. Nessuna impostazione o regolazione. Crimp 30-24 ga. (0,41-0,71 mm) condotto metallico rotondo. Trasforma rapidamente il tuo avvitatore a percussione in un piegatore di potenza.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	Malco
Brand	‎Malco
Color	Black
Color	‎Black
Country of Origin	‎USA
Customer Reviews	4.4 4.4 out of 5 stars 662 ratings 4.4 out of 5 stars
Grip Type	‎Ergonomic
Handle Material	Metal
Handle Material	‎Metal
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	8.25 x 6 x 2 inches
Item Dimensions LxWxH	‎8.25 x 6 x 2 inches
Item model number	‎C5A2
Item Package Quantity	‎1
Item Weight	2.1 Pounds
Item Weight	‎2.1 Pounds
Manufacturer	‎Malco Products
Material	‎steel
Measurement System	‎Metric
Part Number	‎C5A2
Power Source	‎Hand Powered
Product Dimensions	‎8.25 x 6 x 2 inches
Style	‎Crimper
Warranty Description	‎Limited

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Anthony

Absolute wrist saver

I’ve done hvac for over 4 years now hand crimping spiral and snap lock sheet metal and once I bought this my efficiency shot through the roof. Great crimps every single time super easy to use, durable, and easy on your impact great purchase

Scritto da: Kristina Kreitzer

Better than hand crimpers

I’m a union sheet metal worker, and this thing is awesome. A bit of a learning curve l, but once you get the hang of it there’s no turning back. This thing has some weight to it which surprised me at first, but after using it I understand why. I’ve been looking at buying this for about a year, finally pulled the trigger and I’m glad I did. 5 secs is all it takes to crimp a pipe and it’s a close to a factory edge. I stop before the seam afraid to blast through it, though I’m sure it will handle it. Im very happy have to wait to see how long the shank lasts.

Scritto da: Ed

On the pricey side but faster than hand crimping

I was skeptical about buying this because it's not cheap. Hand crimpers are a lot cheaper. But I'm very impressed at how it crimps. It's noisy and you can only use it with a impact. I tried using it with my regular drill and it twisted the pipe and cut my arm so do not use anything but an impact it even has a warning label. But if you're crimping lots of pipe there's no competing with a hand crimper at how fast you can use this. Definitely worth the money if you are made of it.

Scritto da: Scott Messina

Saves your forearms

This is much faster than hand crimping, and far easier on your hands and forearms. I can crimp a 10" duct in about 10 seconds, while it's already mounted. Because this goes on the end of your impact, it can spin 360 to modify duct that's already in the air, as long as you've got 2+ inches all of the way around. Just don't go over a seam, it says so right in the instructions. It takes a few tries to learn the best way to get it fully engaged on the pipe, I just go forward a couple of clicks, then reverse back to the starting point, and it's ready to go. I am using it with a Milwaukee M12 Surge impact, so it's noise level isn't too bad. With a standard impact, it will likely be quite loud, especially when amplified by uninsulated ducting

Scritto da: Jason

Must have? Or nice to have? That’s the question.

It’s quit useful and saves tons of time if your cutting a lot of duct. There is one issue I have come across. I found that using this with fittings, like els, I found the crimp isn’t enough. I need to hand crimp a bit because it’s not quite enough to fit the duct to the fitting. Still worth it and a valuable tool. Is it a must have? I wouldn’t say that. But I’m very happy with it and do recommend it.

Scritto da: Placeholder

Great product

Thus is so fast and saves so much time when installing metal ducting, it’s a great tool

Scritto da: James

Worth it!

If you do much work with round sheet metal ducting this is worth it, in one job I used it so many times I didn’t even think I would need it and it saved so much time, it’s far quicker and results in more professional look than a hand crimper. It takes a little getting used to though but after that it’s awesome

Scritto da: Duct Sealant Joe

Fantastic, but....

Month in and is already wearing out a little bit. Works maybe a little too well. Will over crimp things by a half inch for circular duct. Otherwise it saves my time, and my hands. Would recommend

Scritto da: Tyler little

Beware! Can become a 270$ tool quickly

This thing is awesome! It crimps spiral better than you get from the shop, that being said if you push it too hard or try to crimp over a seam the drive shaft will snap. Malco has you covered though for almost 70$ they will send you a replacement shaft which is little more than a nut driver (10mm I think) with a shoulder at the end to hold it to the tool. If this easily replaceable, and easily broken part was a reasonable price this thing would get 5 stars all day. If you have a friend with a metal lathe maybe you can whittle up a cheaper replacement.

Scritto da: Jeff Arbeau

Forget what you know about crimping! 2ND REVIEW

The media could not be loaded. You have to learn how to use this tool. This crimper is nothing like any way you crimped before. Go low and slow till you ght the fell of it. Wish I had this 20 years ago. I love it!!

Scritto da: Brendon Maclellan

Awesome

This thing save so much time and energy. Love it. Highly recommended

Scritto da: Amazon Customer

Crap

Its crap. It rips apart ductwork and when you are super careful and actually get it to crimp all the way around it doesn't even crimp it enough for it to fit.