Silicone Momentive RTV103, monocomponente, nero, cartuccia da 300 ml

Brand:Momentive

3.9/5

55.96

Sigillante siliconico monocomponente per uso generico che polimerizza formando una gomma siliconica resistente, duratura e resiliente all'esposizione all'umidità atmosferica a temperatura ambiente. Prodotto di consistenza pastosa a resistenza standard che può essere applicato su superfici verticali e sopraelevate dove i sigillanti versabili/autolivellanti non sono pratici. Ha eccellenti prestazioni a bassa e alta temperatura da -75° a 400°f. può essere utilizzato in applicazioni a contatto con gli alimenti dove si applicano le normative FDA riferimento: Cds4319. riconosciuto da UL sotto UL File e-36952.

Soddisfa le specifiche militari mil-a-46106 e lo standard nsf 51, è conforme a fda 21 cfr 177.2600, è conforme a usda e ha componenti riconosciuti da ul. L'intervallo di servizio continuo va da -75 a +400 gradi f (da -60 a +204 gradi c) e l'intervallo di servizio intermittente va da -75 a +500 gradi f (da -60 a +260 gradi c). Aderisce a molti metalli, vetro, ceramica, gomma siliconica e alcune plastiche rigide senza l'uso di primer. La consistenza della pasta consente l'applicazione su superfici verticali o sopraelevate. Sigillante siliconico rtv nero monocomponente di consistenza pastosa per riempire e sigillare fessure o fessure fino a 1/4 di pollice.
Country of Origin USA
Item model number RTV103-300ML
Manufacturer Momentive
Package Dimensions 11 x 1.5 x 0.94 inches; 10.41 Ounces

3.9

8 Review
5 Star
83
4 Star
17
3 Star
0
2 Star
0
1 Star
0

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Wakawaka
Actual silicone is great, packaging no so much
So far I’m in for 7 tubes of this stuff and have had the same issue to varying degrees with all tubes. The plunger bypasses a ton of the silicone! Not only have I lost about 5-10$ worth of product every tube but my electric gun is a MESS. Yes I used a manual version too, and tried adding a fender washer to make sure I was supporting the entire plunger - same issue. I did cut my tips small and noticed that going slow reduced the loss but it shouldn’t be happening at all. Initially the directions fail to mention that you must puncture the inner seal after cutting tip. Not a big deal but threw me for a loop right off the bat because normally only cardboard adhesives have the seal and these tubes are plastic. Actual silicone is great quality, using it for fish tank stuff. I had success bonding acrylic to glass (over flow and sump building) and injecting it to reseal a stupid craigslist tank. One thing to note, if you’re using tape at the seam which you plan to remove while the silicone is still wet to get a clean line, you need to pull it off right after completing the seam. If you wait the typical 5 mins you’ll risk pulling the silicone OUT of the seam with the tape instead of just the excess that ran onto the tape.
Scritto da: ScottH
Sets up pretty quickly
It does grow a skin pretty quick, so you don't have heaps of time to get your bead looking the way you want. I found it stuck a little to the blue tape I was using as a mask. Not a big deal, but be prepared for it.
Scritto da: James daniels
This is what you want for fishtank's also, its black!
This is the best on the market for its application in fishtanks, its wayyyy better than silicone. Worth the expense. Just repaired a 3500 dollar fishtank i bought for 300 bucks with it.
Scritto da: I Buy Too Much
Works Like A Charm!
I chose this item due to the reviews regarding fish tanks. Had to reseal used bow front tank. Used frog tape to make perfect bead lines. Go slow by steady your caulk gun to get one continuous bead. Cut the caulk top to the size of bead you want to achieve. Do one pass with wet finger. Don't use a dry finger!!! Then do not touch it! Have wet paper towels ready as it can be messy. After drying I used a scraper to get off any random caulk. Do not scrap any part of aquarium side/bottom seal.If you made it messy, leave it. You do not want to break the cured seal. I waited until the vinegar smell was gone (about 40 hours as my tank was in garage) to rinse out and set up. Awesome product!
Scritto da: Brent Custer
Perfect
Caulking was perfect no hard spots. Great product and will buy again for sure
Scritto da: Bill
Used it to seal a 26 gallon tank worked excellent
Used it to seal a 26 gallon tank worked excellent
Scritto da: Tom Dehnert
Very strong aquarium safe
The best stuff period for redoing the inside of a fish tank
Scritto da: Mike jones
The best stuff around for Aquariums
Very strong, and very fast drying. Used it to repair damaged seals in a Waterbox rimless aquarium.

Prodotti correlati

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart