Oregon 75-972 Cinghia di ricambio per John Deere M112006, 1/2" x 62-1/4"

Brand:Oregon

2.4/5

55.71

DAL PRODUTTORE Le cinghie di ricambio Oregon Exact sono costruite da CPT-Dayco secondo le dimensioni esatte del produttore dell'attrezzatura originale e sono di costruzione del produttore dell'attrezzatura originale o superiore.

Prodotto non disponibile
Per tosaerba GX70, GX75, GX85, GX95, RX63, RX73, RX75, RX95, SX75, SX85 e SX95. Cinghia di trasmissione della falciatrice. Misura 1/2 pollice per 62-1/4 pollici. Sostituisce il numero di parte John Deere M112006.
Brand Oregon
Color Brown
Compatible Devices Lawn Mower
Customer Reviews 3.4 3.4 out of 5 stars 28 ratings 3.4 out of 5 stars
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 4 x 4 x 24 inches
Item model number 75-972
Item Weight 0.4 Pounds
Item Weight 6.4 ounces
Manufacturer Oregon
Product Dimensions 4 x 4 x 24 inches

2.4

9 Review
5 Star
31
4 Star
20
3 Star
28
2 Star
0
1 Star
21

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Sitka Charly
Ahoffoss was right!
I purchased this belt to replace the original belt on an older but relatively unused GX95. It was 0.3 inches longer and had the same back width but as ahoffoss noted, about .030 thinner from outer to inner face. The initial fit was good although the tensioner was nearer its limit of travel. It mowed for about an hour and a half, then the belt turned over and jumped off at the mower end cutting a small grove in the belt. I replaced it and it mowed about 50 feet, and it twisted and jumped off again this time catching between one of the pulleys and the guard which prevents it from jumping off when the belt is de-tensioned. That cut my new belt nearly in two. Since this event, I replaced it with an John Deere M112006 belt and have subsequently mowed about 20 hours without problem. Ideally, the slight difference in thickness of the belt would not be an issue, but due to the misalignment between the motor pulley and the deck pulley that occurs as the deck is lowered, conditions are far from ideal. I have to conclude that the additional thickness of the belt that John Deere obviously did for a reason is sufficient to prevent the belt from twisting and destroying itself. Bottom line, the Oregon 75-972 is not a direct replacement for the M112006 belt in all applications.
Scritto da: matthew valentine
John Deere M112006
As the description and title say, this belt is a substitute for JD M112006. The Price wasn't too far off the JD price, but I needed it shipped, when I ordered due to personal time constraints. Shipping was quick, proper part arrived and it's worked perfectly for me each week for 3 months now. I'd buy this one again, and if i couldn't get it locally at Tractor Supply, I'd order through this route once again. If you need a M112006, this will suit just fine. Don't hesitate to order.
Scritto da: ahoffoss
Perfect fit,.....Snapped first pass!
Fit perfectly on my John Deere mower. Always need to keep one around just in case. Because it's ALWAYS going to break when you only have a couple more passes to make! Oregon is just as good (and far less expensive) than the replacements from the dealer! *******UPDATE******* Finally got around to mowing again and on the very FIRST pass, the belt snapped in half. Checked to make sure it wasn't something on my mower causing the problem, verified that it wasn't. My original belt (John Deere factory) lasted well over 10 years. This one, not even 10 minutes! It's too bad cause normally Oregon replacements are great. This one did seem slightly "thinner" but overall it fit fine. Guess that little bit of thickness makes a big difference?!
Scritto da: FMC
Dear John
Great belt, but John Deer must surely be incorrectly worded. It should be Dear John, the way you have to practically disassemble the whole unit to simply change a belt!
Scritto da: wayne atkins
Great product, fast delivery
Great product
Scritto da: trip68
For my John Deere GX85
Fit my John Deere GX85 mower deck blades then it wraps around pully. This is not the belt for the engine part! It's for the mower blade part. Somewhat easy fix. Mower works great again!
Scritto da: Amy
Three Stars
It broke after 2 uses.
Scritto da: Pierre Kennedy
Four Stars
Fit as expected and put the mower back in action.
Scritto da: REAL GAGNON
WRONG SIZE
the belt i received was 1/2 inc x 63-1/4 RAN FOR ABOUT 1 HOUR AND BROKE ,,, TOO LONG I PRESUME COMPLETE WASTE OF MONEY CHEERS R GAGNON should be refunded

Prodotti correlati

hot
Candele per tosaerba Oregon 77-321-1
4/5

€ 26.39

Candele per tosaerba Oregon 77-321-1
4/5

€ 26.39

hot
Stens 225-746 Aftermarket, Multi
4.1/5

€ 26.62

Stens 225-746 Aftermarket, Multi
4.1/5

€ 26.62

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart