MOOG 513272 Gruppo mozzo

Brand:MOOG

3.6/5

159.80

TEST RIGOROSI -- Test completi durante i processi di progettazione e sviluppo da parte degli ingegneri MOOG per una qualità su cui contare. PROTEZIONE DA CORROSIONE - I prigionieri delle ruote rivestiti resistono alla corrosione e alla ruggine per una rimozione più semplice e una corretta coppia. FACILE DA INSTALLARE - Progettato e progettato per un'installazione rapida e senza problemi. MANTIENE ACQUA E SPORCO FUORI - Il design della guarnizione a quattro labbri inibisce i danni mantenendo l'umidità e altri contaminanti fuori. DURATA DI SERVIZIO ESTESA - Il design avanzato della pista di rotolamento specifico per l'applicazione riduce lo stress, la rotazione e il calore sui componenti. PRESTAZIONI AFFIDABILI -- Il design preciso della forma del rullo garantisce un precarico costante e ottimale installato in fabbrica per ridurre al minimo il rumore e l'usura eccessivi.

TEST RIGOROSI -- Test completi durante i processi di progettazione e sviluppo da parte degli ingegneri MOOG per una qualità su cui contare. PROTEZIONE DA CORROSIONE - I prigionieri delle ruote rivestiti resistono alla corrosione e alla ruggine per una rimozione più semplice e una corretta coppia. FACILE DA INSTALLARE - Progettato e progettato per un'installazione rapida e senza problemi. MANTIENE ACQUA E SPORCO FUORI - Il design della guarnizione a quattro labbri inibisce i danni mantenendo l'umidità e altri contaminanti fuori. DURATA DI SERVIZIO ESTESA - Il design avanzato della pista di rotolamento specifico per l'applicazione riduce lo stress, la rotazione e il calore sui componenti. PRESTAZIONI AFFIDABILI -- Il design preciso della forma del rullo garantisce un precarico costante e ottimale installato in fabbrica per ridurre al minimo il rumore e l'usura eccessivi.
Bearing Number 513272
Brand MOOG
Item Dimensions LxWxH 7.2 x 6.6 x 5.5 inches
Item Weight 5 Pounds

3.6

13 Review
5 Star
78
4 Star
11
3 Star
5
2 Star
3
1 Star
2

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Andrew
Don’t buy, lasted 5 months
Don’t buy this product. I installed these on a jeep wrangler which they only lasted five months. I should’ve went with the Timkin
Scritto da: Dave
Awesome Wheel Bearing and Hub Assebly
The bearing itself is of the upmost quality. Unfortunately the abs sensor and cable provided is about 1 foot shorter than OEM. I'm pretty sure I will rip the cable out the very next time I go wheeling.
Scritto da: Kalee
Just checked them after 7 months of straight hwy driving.
After 7 months of hwy driving they are still great. Installed on 08 jku. install was super easy. Both sides done in around 3 hours with basic tools in the driveway. Also the wheel speed wire length was perfect for my jeep.
Scritto da: nathan hansen
My jeep has a 4” lift and the sensor wire is long enough.
The moog hub bearing is a nice unit. I replaced both sides on my 2010 jku. I finished in about 4 hours. Granted I fought a froze axle in the driver side and had to do some deleting. Overall should have taken about 2-1/2hrs I’d say. Tools needed. 12 point 13mm socket. 21mm socket or wrench 36mm socket for spindle nut, wire brush( I used a grinder and wire wheel) small screwdriver. Pretty simple job.
Scritto da: James McKee
Included speed sensors not intended for lifted vehicles!
Many of the reviews on this wheel hub where correct about the length of the speed sensor wire. If you have a lifted Jeep JK (mine has a 4 inch lift) and plan to change out the speed sensor wires when you install the new wheel hubs, make sure you buy extra long speed sensor wires separately. There was about a 8 to 9 inch difference between the wire that comes with the wheel hub and what I needed for my lifted Jeep. Other than that the instal went without a hitch. Hope this is helpful!
Scritto da: Amazon Customer
cord short for lifted jeep - easy to fix
I have a lifted Jeep so I needed longer ABS cords, I cut and spliced a section of the old connector with the new one. The black and white wire had to be reversed for it work. Black to white and white to black
Scritto da: D. Harris
Fits lifted Wrangler
A lot of reviews say the connection is too short but this one was exactly the same length as the original. Fit my 2007 Wrangler with a 6 inch lift perfectly.
Scritto da: PSYCHOPATHiO
Great
This is an initial review This product eliminated my death wobble but also at the same time I replace all ball joints with these https://www.amazon.com/dp/B009RP89V6?psc=1&ref=ppx_yo2_dt_b_product_details & also changed my steering stabilizer as it was worn out I tested the car over many bumps on high speed car 1 death wobble 0 <-- I win Don't let anyone tell you it's a track bar drag link... or anything else, mainly it's all related to either a bent pins or worn out bushings or broken ball joints or broken wheel bearings & a steering stabilizer is a must-have.
Scritto da: RickH
Good purchase.
Factory fit at a discounted price.
Scritto da: mike boksteyn
Good product
Perfect fit for my Jeep
Scritto da: A V.
Happy with this product
Installed on Acadia 2013 to replace very noisy bearings. Very happy with it, no more unbearable noise!
Scritto da: Bernatchez Serge
Pas exactement pareil
Fillage pas assez long J’ai du le passer autrement
Scritto da: Steve
Parfait pour Jeep wrangler Unlimited X 2007
Reste plus qu a voir l endurance mais, pour l instalation, c est exacte. Même dimension et même longueur de câble que l original

Prodotti correlati

hot
Set di cuscinetti TIMKEN SET34
3.7/5

€ 36.11

Set di cuscinetti TIMKEN SET34
3.7/5

€ 36.11

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart