HHIP 4002-0018 R8 TAGLIERINA A MOSCHE CON ATTACCO 2-1/2" TESTA 5/16" Codolo R8

Brand:HHIP

3.3/5

€
74.18

R8 Fly Cutter con gambo con testa 2-1/2 ~ Utilizza punte per utensili standard 5/16. ~ Controbilanciato. ~ Realizzato in resistente acciaio temprato. ~ Taglia superfici piatte e lisce con un solo taglio.

Prodotto non disponibile

EAN: 0769053033006

Categories: Strumenti e miglioramento della casa, Prodotti industriali e scientifici, Utensili elettrici e manuali, Parti e accessori per utensili elettrici, Parti e accessori del router, Bit del router, Pezzi di falegnameria,

Taglia superfici piatte e lisce con un solo taglio. Realizzato in resistente acciaio temprato. Controbilanciato. Utilizza punte per utensili standard 5/16.

Country of Origin	USA
Item model number	4002-0018
Manufacturer	ABS Import Tools, Inc.
Product Dimensions	6 x 3 x 3 inches; 2 Pounds

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Jeffrey Jenkins

Performs well, but is for 3/8" bits, not 5/16

Like others have reported, I received a 3/8" bit fly cutter, despite that the description (still) says it is for 5/16" bits. That wasn't a problem for me - in fact, I was kinda hoping I'd receive the 3/8" size - but I docked a point for the misleading description, anyway. Functionally, this fly cutter is very well balanced and produced just barely perceptible vibration at 600 RPM, and a lot less clatter when actually cutting than a much smaller fly cutter with a straight 1/2" shank. Also, there was no difference in bit height above the fixed jaw of my vise when rotated 180 degrees, which means no wobble. Shown is a test cut in 6061 aluminum plate at 0.1mm depth of cut, 600 RPM and hand-cranking the travel at a reasonable speed on my PM-727M mill - very pleased with that result, and I suspect that a HSS tool bit will give even better results, especially in aluminum (I just need to grind one - all I had on hand was a 5/16" bit for the aforementioned smaller fly cutter).

Scritto da: daniel

The pocket clip breaks easily if used in pocket all day

great ruler just the pocket clip lasted about a week before it broke off one of the wings

Scritto da: chuckspb

Nice R8 fly cutter

I was going to deduct a star or two because of the threads in the arbor. They were started on an angle and my draw bar would not start without trying to cross thread. I was ready to return it but decided to try a repair. Luckily I got the threads started straight after chamfering the end and got a good inch of threads in it, so all is well. The cutter its self is very nice and will hold a 3/8 left hand cutting tool very nicely. It runs true and makes a very smooth cut. The balance is very good at 900 RPM in my Grizzly G0705 mill. I'm quite happy.

Scritto da: Ma

the ruler is very hard to read

I do not recomend this ruler. It is very hard to read with the tiny numbers and lettering.

Scritto da: Elaine

Cut for 3/8" tool bit not 5/16"

Which is good because I have 3/8 bits and it worked well. Also, not blued but all white, which made no difference to me but it may to you.

Scritto da: Donald Cooke

Works fine

Wish the set screws were safe instead of metric

Scritto da: E. Motley III

Solid, accurate, bargain.

Exactly what I needed. Solid, with four grub screws, and the taper fits tight even before threading in the draw bar. If you need a fly cutter, and don't have the infinite patience to machine your own (I'm looking at you, This Old Tony), grab this one and some high speed steel stock and get cutting.

Scritto da: Saúl S.

Buena relación calidad/precio

Se ven de buena calidad, no he podido cortar bien con ellos pero supongo que eso se debe mas a mi incspacidad de afilar los buriles, voy a intentar con un inserto de carburo a ver si tengo mad suerte, pero por el precio me parecieron buenas herramientas.

Scritto da: Caribbean Traveller

Junk made in India

Had it said where this was made, I would have known not to order it. Just junk, worse than made in China, will be returning. Don’t bother.

Scritto da: Jason Stevenson

nice size, great price.

this is the bigger set of all the three piece sets of fly cutters on the market. I used them and they work great. it really comes down to the cutter bit you use, and on what material. overall completely satisfied.

Scritto da: mike

fits a 3/8 tool

mine looks slightly different then the image ( it hasnt been blackened) but was happy to find that my 3/8s carbide lathe tooling. leaves an unmatched surface finish

Scritto da: Amazon Customer

Bon produit.

Bonne grosseur pour ce genre de travail, livraison rapide.