Fuji Spray 2903-T70 Mini-Mite 3 Platinum - Sistema di spruzzatura HVLP T70

Name: Fuji Spray 2903-T70 Mini-Mite 3 Platinum - Sistema di spruzzatura HVLP T70
Brand: Fuji Spray
SKU: 0612852903707
Price: 1477.16 EUR
Availability: InStock

Brand:Fuji Spray

3.7/5

€
1477.16

DESCRIZIONE DEL PRODOTTO Il sistema Mini-Mite 3 PLATINUM include la pistola a spruzzo Fuji T-Model. Fuji installa lo stesso potente motore a turbina a 3 stadi utilizzato nei modelli Q3. L'MM3 PLATINUM non ha la funzione brevettata di riduzione del rumore come si vede sui modelli Fuji Q, tuttavia il livello di rumore non è superiore a quello di qualsiasi altra turbina HVLP standard. La turbina MM3 PLATINUM sviluppa circa 6psi. Questa è una pressione più che sufficiente per spruzzare tutti i rivestimenti noti (se opportunamente diluiti) e tutti i nuovi rivestimenti a base d'acqua. La pistola a spruzzo T-70 è senza spurgo e presenta una manopola di controllo del ventaglio montata lateralmente (per regolare la dimensione del ventaglio) e una tazza da 1 litro. Il set di cappucci aria standard n. 3 (1,3 mm) è destinato all'uso di finiture di precisione per uso generico. Facile da mantenere. Perfetto per professionisti o principianti. Questa è una macchina industriale ad un prezzo imbattibile. Robusta valigetta in metallo con supporto per pistola. Portatile e potente. Il sistema include la turbina Mini-Mite 3 PLATINUM, il tubo flessibile Hi-Flex da 25 piedi, la pistola a spruzzo senza spurgo T-70, la tazza di viscosità, la spazzola per la pulizia, la chiave inglese e il manuale utente di 24 pagine. Cosa c'è di nuovo nella serie Mini-Mite PLATINUM? La camera di dissipazione del calore Fuji Spray: Fuji Spray ha progettato un metodo unico per rimuovere qualsiasi accumulo di calore dalla cassa della turbina. Il calore in eccesso viene convogliato in una camera di dissipazione del calore situata nella parte posteriore del case. Coperture per la riduzione del rumore dello spray Fuji: le turbine Mini-Mite PLATINUM sono dotate di un metodo per ridurre il rumore. Le coperture per la riduzione del rumore ospitano i filtri. DAL PRODUTTORE Il sistema Mini-Mite 3 (MM3) include la nuova pistola a spruzzo Fuji serie T dotata di una manopola di controllo del modello per regolare la dimensione della ventola da piccola a grande. Fuji installa lo stesso potente motore a turbina a 3 stadi utilizzato nei modelli Q3. L'MM3 non ha la funzione brevettata di riduzione del rumore come si vede sui modelli Fuji Q, tuttavia il livello di rumore non è superiore a quello di qualsiasi altra turbina HVLP standard. La turbina MM3 sviluppa circa 6 psi. Questa è una pressione più che sufficiente per spruzzare tutti i rivestimenti noti (se opportunamente diluiti) e tutti i nuovi rivestimenti a base d'acqua. La pistola a spruzzo inclusa in questo pacchetto è la Fuji T-70 con tazza da 1 litro. Il set di cappucci dell'aria standard n. 3 (1,3 mm) è per l'uso di finiture di precisione per uso generale. Facile da mantenere. Perfetto per professionisti o principianti. Questa è una macchina industriale ad un prezzo imbattibile. Custodia in metallo resistente con supporto per pistola. Portatile e potente. Il sistema include la turbina Mini-Mite 3, il tubo Hi-Flex™ da 25 piedi, la pistola a spruzzo senza spurgo T-70 con tazza da 1 litro, tazza di viscosità, spazzola per la pulizia, chiave inglese e manuale utente di 20 pagine.

Quantity

Aggiungi al carrello Compra subito

EAN: 0612852903707

Categories: Strumenti e miglioramento della casa, Vernici, trattamenti per pareti e forniture, Forniture e strumenti per la pittura, Applicazione della vernice, Spruzzatori di vernice,

Il tubo da 25 piedi include una valvola di controllo dell'aria per ridurre l'overspray e il rimbalzo. Custodia per turbina in metallo con pratico supporto per pistola. PLATINUM Turbina con Camera di Dissipazione del Calore (HDC). Pistola a spruzzo leggera senza sbavature con impugnatura ergonomica Stay-Cool. La pistola a spruzzo professionale è dotata di una comoda manopola di controllo del getto laterale per regolare le dimensioni del ventaglio da piccolo a grande.

Brand	Fuji Spray
Color	Blue
Customer Reviews	4.7 4.7 out of 5 stars 449 ratings 4.7 out of 5 stars
Hose Length	25 Feet
Included Components	25ft Air Hose, T-70 Bottom Feed Spray Gun, Mini-Mite 3 PLATINUM Turbine
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	15 x 9.5 x 14.75 inches
Item model number	2903-T70
Item Weight	28.1 pounds
Item Weight	28.13 Pounds
Manufacturer	Fuji Spray
Material	Metal
Model Name	Fuji Spray Mini-Mite 3 Bottom Feed PLATINUM
Power Source	AC
Product Dimensions	15 x 9.5 x 14.75 inches
Style	Portable,Ergonomic
Tank Volume	0.25 Gallons

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: PJ

Great sprayer for woodworking

Before purchasing this sprayer, I had used a Graco 360 DSP airless sprayer with primer and latex paint on built-in shelving. The airless sprayer provided a nice finish on horizontal surfaces painted separately from the whole (adjustable shelves), but I couldn't get good results with assembled pieces because it laid paint down so quickly that there was zero room for error. Each pass had to be timed perfectly, and overspray was a big issue (onto surfaces painted minutes earlier but that had already started to dry, and especially in corners where painting at an angle rather than perpendicular due to the tight space caused excess paint to gather in corners and then drip and puddle). The amount of sanding and rework was unbearable, the over spray area was THICK with paint, and it used a LOT of paint. So, for my next built-in shelves I got the Mini Mite 3 with bottom cup. It worked great. Definitely get the additional whip hose and any remote control outlet. The over spray was comparably minor, it used a lot less paint, and produced great fine finish results at a slow pace for detailed work. The sprayer, cup, hose, and turbine housing are all top notch quality. Clean well after each use and it'll look good and perform well for a long time. My only frustration with cleaning was the plastic diaphragm inside the cup. I had to remove it every time to clean out paint that got behind it. Otherwise, the gun cleaned easily with the separately available cleaning kit. Definitely get that, or something similar. Water flow was not good enough to fully clean inside the feeder tube or inside the gun. After doing all I could with just water, the long, flexible pipe cleaner of the proper diameter got more paint out. I'll still use the airless sprayer for large flat surfaces, but I'll use this Fuji HVLP for all furniture projects. I had to practice a LOT on scrap wood to get the process right, but the resulting finish with a high gloss white latex paint was perfectly smooth. I'm an amateur, and I realize latex paint isn't ideal for cabinetry, but I wanted to exactly match the rest of the existing doors and trim work. I tried the #5 1.8 tip but couldn't get the finish "fine" enough (maybe due to inexperience). I ultimately used the included 1.3 tip and just diluted the paint with water until I got a 20 second pour with the included viscosity cup and ignored any dilution guidelines on the paint can. That produced great, smooth, glossy results. The one trick that helped me the most was having a large piece of cardboard or resin paper to the side of my workspace to test the spray pattern every time I adjusted the width and horizontal/vertical orientation for the various pieces and angles of the shelving. My amateur guide to getting a fine finish is to use the 1.3 tip no matter how thick your paint is, dilute to the 17-25 second range as measured by the viscosity cup, set your spray fan orientation and width, maximize air flow, fully close the paint flow control dial then open it a full turn, then spray briefly in one spot. If you see ANY spatter droplets on the outside edges, then reduce paint flow slightly and try again until there is NO spatter at the edges and you see only very fine spray everywhere. Then run a test pass or two on that paper to determine how quickly you need to move. Place a work light where you can see the wet paint reflection to verify that you have a good coat (this is especially important when painting white topcoat over white primer or when doing a second coat). Overlap passes by 50% (aim the center of the pattern at the far edge of the previous pass. If the reflection looks uneven or grainy due to lack of paint from moving too quickly, it's okay to quickly touch up freshly wet areas with short passes (this sprayer doesn't spatter when you start and stop, so I found it ok to touch-up spots in the middle of a pass without redoing the whole pass), but don't go back to touch up any area that may have already started to skin over (several passes back). Let it dry and do another coat if necessary. A word on over spray... it exists. Do not think that you can spray indoors or in a garage without taking the time to tape off the surrounding area with plastic. There was a fine mist of paint on the (plastic covered) floor or wall past wherever I had aimed the sprayer, and there was a fine, dry, thin, dusty layer throughout the whole room (and garage workspace) afterward far from where I was spraying. That paint dust was as easy to wipe off as a month of normal busy household dust, although I didn't wait to see what happened if I let that latex dust sit for a month. I wore a headlamp and could see fine spray dust floating everywhere, so wearing a respirator is important. The professionals probably do a better job of fine tuning the air flow to reduce this spray dust, but amateurs beware. Still, it's significantly less messy to work with than an airless sprayer, and you have much more fine control, and fine finish results.

Scritto da: Ryan S.

Great HVPL for the price

Was doing research on a HVLP sprayer for woodworking projects. I found good reviews on the FujiSpray systems. I went with the Mini Mite 3 Platinum with bottom feed spray gun. I have used a couple of times now a have had great results. The turbine is powerful and the gun provides a great finish. All the parts are heavy duty and easy to clean. I would recommend this HVLP for anyone who does small finishing products.

Scritto da: JakeB

Great sprayer

This is my first experience with an HVLP sprayer. It was very easy to use and figure out. The instructions were easy to understand and it left a perfect drip free finish. Would happily buy it again.

Scritto da: Jon

Well made and very nice gun!

The T70 spray gun is the best HVLP gun I've ever held in my hands. The turbine unit delivers an astonishing amount of air flow while being moderately quiet, (quieter than some compressors I've used.

Scritto da: Travis Mizzell

Excellent spray setup!

This setup is awesome. After years of spraying professionally in a custom cabinet shop, I was looking for a setup that could meet those type expectations in a hobby/semi professional type setting. This setup definitely meets those needs!

Scritto da: Samantha

Do-it-Yourself Professional Looking Trim and Cabinets

I am an avid do-it-yourselfer only when I am confident I can achieve professional looking results. Performing a whole home remodel over the past year, you can only imagine the number of surfaces that needed painting. Breaking out a roller was fine for the walls, but I definitely wanted a smooth, professional finish for my kitchen cabinets and trim work. After receiving $8-$13K quotes for painting my kitchen cabinets, I researched and decided to buy the Fuji Mini-Mite 3 T70. Thus far, It has been the best investment I made in equipment. Three things I would advise: 6 Ft. Flexible Whip Hose - Buy it! After reading other reviews, I am definitely glad I purchased the whip hose. It is much lighter and makes holding the spray gun a bit easier. Note: I have been spraying 17 ft trim boards outside and noticed that in the heat, the hose would separate from its coupling. This caused the gun to sputter paint all over my boards forcing me to stop, clean up the board and restart. I finally grabbed some zip ties to keep the whip hose attached to its fitting. Quick Connect Couplings: Completely worth having. It makes it so much easier to connect/disconnect the hose from the turbine when hot and moving things around. Wireless Remote - I bought a wireless remote for use with the sprayer so I didn't have to walk 20 feet back and forth to turn it on and off. It makes a difference when painting. I keep it in my pocket or on a hook in my spray booth so I can easily transition between tasks. Cleaning - Run a little mineral spirits through the gun after cleaning. It's an extra step that really helps keep it clean and lubricated. Also buy a longer bristled brush to get to the top of the paint feed tube. Carefully follow directions on how to clean the gun. Don't let paint sit overnight in your gun. The solids will settle and clean up is not fun. Painting - It took several passes and three coats to achieve the nice finish I wanted but I am very pleased with the results thus far. Definitely perform thin coats and build to your final. Although I haven't gotten to the cabinets yet, the baseboards and door casings have come out fantastic. Spray Problems - I had one issue with spraying. It was related to allowing paint to sit overnight in the cup. All of the solids settled and I couldn't stir the paint enough to keep it from clogging the filter. After stirring twice and a few failed passes, I replaced the filter and started over. Obviously, my error. Overall, this was a great investment for me. I'm sure there is comparable equipment and accessories out there, but if you are on the fence about the Fuji you won't regret it.

Scritto da: Kevin E.

Foam filters do a good job stopping any contaminants including overspray

Machine works as advertised. Must be kept away from the spray area so it does not ingest overspray. Foam filters do a good job stopping any contaminants including overspray. The only complaints are that it is quite noisy, definitely hearing protection recommended and the quick coupler between the hose and spray gun is quite easy to inadvertently disconnect with just a bump. It's nice that the gun is easy to disconnect but perhaps a bit too easy. I plan to change this. All in all a good machine for the price.

Scritto da: Amazon Customer

Very well made

Small, compact and powerfull turbine. I really enjoy using this HVLP. Thank you #fujispray

Scritto da: erik

Excelente máquina para pintar

Me.encanto la máquina de pintar fuji está hecha de buenos materias luego luego se siente la calidad del producto y deja unos acabados perfectos aún cuando no tiene uno experiencia en este ramo de la pintura .excelente la recomiendo mucho.