CURT 55537 Cablaggio rimorchio personalizzato a 4 pin lato veicolo, adatto a Dodge Caravan, Grand, Chrysler Town e Country selezionati

Brand:CURT

3.6/5

72.72

Se il tuo veicolo non è dotato di cablaggio per il traino di un rimorchio, il cablaggio personalizzato CURT è la soluzione ideale. Un cablaggio personalizzato, chiamato anche connettore a T, è un semplice dispositivo elettrico plug-and-play che si collega al sistema elettrico dell'auto e fornisce una connessione di cablaggio del rimorchio standard e universale. Questa operazione viene eseguita utilizzando due o più connettori specifici per il veicolo e compatibili con gli OEM da inserire nel gruppo fanale posteriore, eliminando la necessità di tagliare, giuntare e saldare durante l'installazione. I cablaggi personalizzati sono realizzati in modo specifico per il veicolo e, sebbene non siano disponibili per tutti i veicoli, offrono uno dei modi più rapidi, semplici e sicuri per cablare un veicolo per il traino. Questo particolare cablaggio plug-in fornisce una presa per connettore piatto a 4 vie ed è progettato per essere un cablaggio personalizzato per adattarsi a determinati anni di Dodge Caravan, Dodge Grand Caravan e Chrysler Town and Country (per verificare la compatibilità del veicolo, vedere le informazioni sull'applicazione ). Viene fornito con tutti i componenti di cablaggio necessari per stabilire un collegamento affidabile del cablaggio del rimorchio, nonché una copertura antipolvere per mantenere pulito il connettore quando non viene utilizzato. Hai in mente un'immagine della tua prossima destinazione: forse è la barca che approda nel tuo punto di pesca preferito, forse è un campeggio che si affaccia su uno dei capolavori della natura, o forse è il prossimo grande cantiere. Tuttavia, trasformare quell'immagine in realtà richiede molto più che sognare ad occhi aperti. Ci vuole una connessione solida e la giusta quantità di energia.

COPERTURA POLVERE. Per promuovere un uso duraturo e la resistenza agli agenti atmosferici, questo cablaggio per illuminazione a 4 poli per rimorchio viene fornito con una copertura antipolvere in gomma. Si adatta facilmente al connettore piatto a 4 vie quando non viene utilizzato, proteggendolo dagli elementi esterni. PRESA FACILE. Collegare il cablaggio del rimorchio e le luci del rimorchio è facile con il design ergonomico di questa presa per veicoli. È dotato di linguette in alto e in basso per una presa migliore quando si collega o si scollega il rimorchio. SPECIFICO DEL VEICOLO. Questo cablaggio aftermarket per veicolo-rimorchio è progettato per anni selezionati di Dodge Caravan, Dodge Grand Caravan e Chrysler Town and Country. CONNETTORE STANDARD. Questo cablaggio plug-in per rimorchio a 4 piatti può essere utilizzato per collegare le luci posteriori del rimorchio, le luci di segnalazione dei freni e gli indicatori di direzione. Il cablaggio della luce del rimorchio a 4 vie è popolare su una varietà di rimorchi, aggiungendo opzioni di traino versatili per il tuo veicolo. FACILE DA INSTALLARE. Nessun taglio! Nessuna giunzione! Questo kit di cablaggio del rimorchio si collega al cablaggio di fabbrica esistente sul veicolo e lo dota di un connettore di cablaggio del rimorchio a 4 pin posteriore standard per il collegamento e il traino di un rimorchio.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.6 4.6 out of 5 stars 196 ratings 4.6 out of 5 stars
Exterior ‎Smooth
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 4 x 3 inches
Item model number ‎55537
Item Weight 0.31 Pounds
Item Weight ‎5 ounces
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎55537
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎55537
Product Dimensions ‎9 x 4 x 3 inches

3.6

13 Review
5 Star
74
4 Star
17
3 Star
3
2 Star
1
1 Star
4

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Keith
Quick and easy
This was very easy to install, less than 20 minutes. Works great.
Scritto da: Tricker
Towing with lights is good
Read instructions, installed, lights up my trailer. Saved a bunch of money diy baby!
Scritto da: Alicia Mick
Ok
I wish there was a way to route it a diffrent way but had to come out the back when I use it because of the stow n go but it works fine just tuck it back in the trunk when not using
Scritto da: D. WALTER
Took a little maneuvering to install
When I bought this trailer light wiring harness for my 2005 Chrysler Town and Country, I thought it would be the same as with my 2005 Dodge Durango, and go on in a couple of minutes, but I was severely wrong. With this wiring harness, you have to push the ends of the wiring harness through a couple of prefab holes in your auto body. The problem with this is that there is insulation between the interior and exterior body panels, and the holes you need to push the wiring harness through can get pretty tight. The left side tail light was fairly easy with a larger hole in the body panel, I was able to put my hand in farther, and push the wiring harness easier. The Right side taillight was a little harder because the body panel hole on the interior was smaller, and a little lower than the exterior hole, so much more difficult to maneuver through the body. We ended up cutting the end of the right side wiring harness off, and running the wire through the panel, and then reattaching the harness end to the wire once it was through the body. Also, something I wasn't aware of with this harness is that the 4 pin connector is not maintained on the outside of the vehicle. This wiring harness stays inside the vehicle until you are ready to use it, and then you run the wires out through the back door whenever you're going to use it. The part I don't like about this harness is shutting the door on the wires. I know that there is weather stripping there, and it probably won't cut the wires by being closed on them, but I just feel it might degrade the life of the harness... Otherwise, so far so good. Decent wiring harness, somewhat difficult installation, but still functional, and decent quality.
Scritto da: Nicholas Maddox
Easy to install
Easiest install for any wiring project I’ve ever done!
Scritto da: John F
Quick use!!
Took about 5mins to install. I did not run it back through the body. I just ran the wires under the light assembly. Then pushed the wires inside the van 5mins tops. Didn't care for the ground wire. Had to use a drill Tel screw to the body. They could've tied that into the other white wires since the body harness for the lights is already grounded. Other than that no problems.
Scritto da: Keith J Rigden
Get it
Pretty easy to install in my 06 Grand Caravan. Routing to the passenger side requires you to fish it to the light cavity. Get a good look at what's going on there before you tie on. Wish the set was longer. Watched one video, but it was for another brand. This product is too short to route it their way, which is a little cleaner, but not a big deal. Only reason for knocking a star off. Worth every extra penny to not have splice anything!!
Scritto da: Ashish Desai
Very easy to install and worked with no issues
The harness is super easy to install on a 2005 dodge grand caravan sxt stow and go. Took about 20 minutes with no prior experience of knowing anything dodge or harness wiring. The self tapping ground screw worked instantly under the gamble and the length of excess wire is about 15 inches which is plenty to reach my trailer. Literally you can do this by watching a YouTube video on your phone and doing it same time. Definitely buy this kit and do not pay to get it installed ..you can do It yourself
Scritto da: Kevin from Calgary
Works well for my little trailer with LED lights.
Works well with my little trailer. Note that this kit does not contain a powered converter, so your trailer lights are powered from the vehicle's tail light wiring. If your small trailer has LED lights, this setup is fine. On my 2005 Grand Caravan, this kit will allow the trailer connector to extend outside the tailgate by a foot, or perhaps a little more. It takes a fair bit of cutting in the existing tail light wiring grommets for the hole to be large enough to push the connectors through to the space behind the taillights. That small tube of black silicon sealant is to reseal the grommet where you cut through. I used coil-style plastic wire loom to protect the wiring as it exits under the tailgate.
Scritto da: JP
Price was right, easy to install
Great price point, installed on an 04 caravan, took about an hr but never installed a trailer harness before. Good product!
Scritto da: Mr.Kent
works great.
no problems, works great.
Scritto da: Amazon Customer
... cable cannot be stored in the tire jack compartment like the other brand
It works with the exception that the plug is very tight and the cable cannot be stored in the tire jack compartment like the other brand. Minor problems. Seems to work OK.
Scritto da: Dompti
????
Parfait mais je l’es retourner je n’avais plus besoin.

Prodotti correlati

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart