Briggs & Stratton 190627GS Collettore di scarico pompa idropulitrice

Name: Briggs & Stratton 190627GS Collettore di scarico pompa idropulitrice
Brand: Briggs & Stratton
SKU: 5557890014730
Price: 101.83 EUR
Availability: InStock

Brand:Briggs & Stratton

3.4/5

€
101.83

Non include guarnizioni o o-ring. Sostituisce anche il numero di parte Briggs & Stratton 190574GS. Codice articolo Briggs & Stratton 190627GS.

Quantity

Aggiungi al carrello Compra subito

EAN: 5557890014730

Categories: Patio, prato e giardino, Utensili elettrici per esterni, Parti di ricambio e accessori, Parti e accessori per idropulitrici, Pompe,

Non include guarnizioni o o-ring. Sostituisce anche il numero di parte Briggs & Stratton 190574GS. Codice articolo Briggs & Stratton 190627GS.

Country of Origin	Italy
Customer Reviews	4.3 4.3 out of 5 stars 116 ratings 4.3 out of 5 stars
Is Discontinued By Manufacturer	No
Item model number	190627GS
Item Weight	0.01 ounces
Manufacturer	Briggs & Stratton
Product Dimensions	3.25 x 3.25 x 4.25 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Tom T

The right part, Pressure Washer Parts

I was hoping to get a Pressure Washer Manifold with all of the many parts already in the manifold. This one has just the bare manifold. After reading another review, I went to Ebay to get one for less money that was completely assembled, everything included. The real price of this unit on Ebay with all of the parts was $120. I didn't feel my old power washer was worth that much so I ordered the manifold from Amazon. It did take some careful dismantling of the old part and some pictures of the process with my phone. I was able to get all of the very small parts into the new manifold and put it on the washer. It works perfectly. I'm not a small engine fix-it guy so I was very happy to have accomplished this with no problem. The Briggs & Stratton 190627GS fit perfectly on my old unit.

Scritto da: nikboom

Great repair manifold for my Troy Built Power Washer

Great repair manifold for my Troy Built Power Washer, the original manifold has a poor tread attachment for the hose which wears in time. Used a Lasco 60-1057 brass fitting for the hose fitting. 3/8" NPT x 22MM adapter. I had to cut the very back of the old manifold off then use a punch to drive out the water load regulator and also the output regulator or you can certainly buy a new one for 45 bucks. I also bought a Briggs and Stranton 193806GS Pressure Washer Pump Valve Check Kit to replace the original valves in the pump.The water regulator is hold on by a U-clip and the out put regulator is comprised of nylon and a spring. You need to cut the very back or the old manifold metal or you will destroy the internal parts by cutting into them.....then use a punch to drive them out.

Scritto da: Gary Waller

manifold replacement part

Worked great to fix my problem. This cast aluminum manifold replaced the cracked one on my Coleman pressure washer, that cracked because it held water over the winter. I will now always make sure the pump drains completely before storing over the winter. I took a gamble that this would fit the Coleman, since it looked the same by the pictures, and it was. You have to be a bit mechanical to figure out how to replace the internal parts, but it wasn't too bad to get done. By using my parts and this housing, I saved $40 over the price of a kit. I did read on line that the adjustments to the pressure setting must be done properly, or the manifold housing can crack from too much pressure: Steps on adjusting the pressure setting: 1. Start washer while pulling the trigger and holding open. 2. Using a wrench, adjust the nut clockwise. 3. As the nut is adjusted, the pressure will increase. 4. When the PSI in no longer increasing, stop adjusting. 5. Turn the nut back counter-clockwise 1/4 to 1/2 turn. 6. Release trigger and engine should idle down (not be laboring.) 7. Pull trigger again to re-test unit. 8. If all is okay, tighten the small lock nut in place.

Scritto da: Jim

This thing is a bugger

The manifold arrived quickly, and once installed worked fine. After a very cold winter I found that the original one apparently still had some water in it and had frozen. Thank goodness it was already cracked, because I had to finish cutting it apart to get the guts out of it for the new one. I tried to find one with new seals and springs in it, but couldn't, and since the price of all new parts plus the manifold itself would have been 2/3 the cost of a whole new washer I chose to reuse the old ones. Like I said, once installed, it works fine but it was a bugger to get the old one apart.

Scritto da: Jody

Missing crucial parts

There was a ball within the old unit that wasn't sent with the new unit and the description failed to mention this. We had to go to several small machine shops only to find out that the way to get to that ball is to cut the old part into pieces to access it. The description of this unit could've been much better and the pictures as well.

Scritto da: Handyman06

Pressure Washer manifold

The manifold replacement worked well. Both the manifolds (orig and replacement) are made of a softer metal than I would have expected. If you live in a cold weather area make sure the washer is totally drained (blow it out) or you could get a crack along the screw line. If I were going to do it again I would order the total manifold with all the internal components installed. I spent a lot of time pulling, prying and cutting the parts out of the old one. It works fine but there is a chance you could mess up any of the many internal components as you swap them out.

Scritto da: Shawn Gallagan

Learn from my mistake.

This part is fine, but learn from my mistake and buy one with all of the internal components pre-installed. Some of the plastic components were difficult to remove from my old manifold and I accidentally scarred up a few of the pieces. Edit: I eventually found replacements for the internal pieces that I damaged, but I ended up spending quite a bit more than I would have if I had purchased the manifold with all the parts pre-installed. I've been using it for about a month now and it seems to work great.

Scritto da: Amazon Customer

right part and it fits but does not include the neccessary internal pieces

the internal components i.e... check ball, plastic inserts, spring are not included. must remove from old unit.