0
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister

Bennett HYDBOLTCON Kit di conversione da idraulico a elettrico BOLT

Brand:Bennett Marine

3.2/5

€
566.69

Tutto ciò di cui hai bisogno per una conversione rapida e semplice dagli attuatori idraulici Bennett agli attuatori elettrici BOLT di Bennett. Gli attuatori BOLT sono eccezionalmente durevoli e affidabili..

Prodotto non disponibile

EAN: 0666285600276

Categories: Sport e tempo libero, Sport e forma fisica, Canottaggio e vela, Barche e attrezzature, Hardware, Hardware del ponte,

Dotato di retrazione automatica della linguetta e modulo relè diagnostico. Connessione Plug 'n Play al tuo interruttore a bilanciere Bennett standard esistente. Non è necessario ricablare o praticare nuovi fori. Conversione rapida e semplice dai sistemi idraulici a singolo attuatore Bennett standard utilizzando il cablaggio, l'interruttore a bilanciere e i piani di assetto esistenti.
Brand ‎Bennett Marine
Country of Origin ‎USA
Customer Reviews 4.1 4.1 out of 5 stars 72 ratings 4.1 out of 5 stars
Item model number ‎HYDBOLTCON
Item Weight ‎9 pounds
Manufacturer ‎Bennett Marine
Manufacturer Part Number ‎HYDBOLTCON
Model ‎Hydboltcon
Product Dimensions ‎15 x 8 x 7 inches

3.2

8 Review
5 Star
64
4 Star
9
3 Star
13
2 Star
3
1 Star
12

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Gary W
Good kit but errors in instructions
I bought this kit to upgrade another company's automatic trim tabs on my boat to powered tabs. It worked well. I had to drill new holes in the old stainless steel 11x9 tabs. Instead of following the directions to route the cable through the transom in the middle of the upper mount, I chose to run the cable higher on the transom to keep it above the waterline. I used a hull pass-through fitting for those. I also bought a Bennett BRC4000 switch assembly for the dash. Since I was not converting from an existing system, I cut off the 4-pin connector on the module cable and spliced the wires to a 4-wire extension cable to go to the switch. The switch had to be modified by removing all jumpers and wires and starting over with new jumpers and the wires from the extension cable. See the attached sketch. The module works this way, each of the 4 inputs (port,starboard,up, down) are activated when 12vdc is applied to each one from the switch. A minimum of two inputs must be activated for any operation to occur, one for the side (port or starboard) and one for the direction (up or down). Both port and starboard can be active at the same time (port, starboard, and up for example) by putting 12v to 3 of the 4 inputs. There are two errors in the installation manual. One has you populating only 2 of the 3 mounting holes on the upper actuator mount, even though there are 3 screws supplied. The other error is that the instructions state that the power LED at the bottom of the module will be lit whenever there is power applied to the module. That is not true; the LED is on only when the actuators are being driven up or down. The self retraction feature works well except that it overdrives the motors far longer than necessary. This kit is actually less expensive than buying just the two actuators by themselves, so if you need the actuators, buy this kit. The self retracting relay module would normally cost another $50 at least. So this is a bargain compared to the prices of the individual parts.
Scritto da: Brett E. Batchelor
Plug and Play
I have an older 1997 Carver 260SE and the old Bennet system was leaking bad. I thought that I can fix it, but every season it got worse. I finally broke down and, originally was going to use Lenco conversion. That was considerably more money. I got the HYDBOLTCON last Friday and literally had it installed on just a few hours. Spent more time cleaning the mess from the old system. My wife and I are optimistic about plug and play stuff, but this worked out perfectly. I did not use the purple wire to have the tabs retract when the ignition is off, but it was a nice option. The main controller mounting lined up perfectly with the old holes from the hydraulic system. For us we did not have to drill a single hole. You will need to download the instruction, or use your phone. My 10 year old could have installed this. Great job Bennet! Thank you
Scritto da: Lawrence
bye bye hydraulic fluid
love my new electric trim tabs. bought this setup to replace an old leaking hydraulic system. Super easy to install. hydraulic is superior in some ways but I got tired of dealing with leaks. these electric ones will never leak hydraulic fluid ;-) They do seem to be a little louder and go up and down a tiny bit slower than the hydraulic ones, but are otherwise great. I am so glad to not have to deal with stinky atf and leaking hydraulics. I did run into a weird issue where I had my original switches plugged into one 12v battery and the trim tab relay plugged into another 12v battery and they wouldn't work! A quick email to bennett and they helped me solve the issue lickety split!
Scritto da: Alcide Castan
Not worth your money
worked for less than a week
Scritto da: Real Image Hydro
High Quality. These are perfect. They work perfect, Super easy to install!
Super easy to install. i deleted my old controller all together. made more room in my bilge area. its CLEAN no more oil mess to deal with. this is the only way to go. I have been boating for 30 years and thirty years of my former Bennett hydraulic units. love Bennett products just couldn't deal with the oil mess any longer.
Scritto da: Drew Hanson
Not for short ram tabs!
Make sure you know what you’re buying. These are only for standard size Bennett trim tabs. Unfortunately they don’t work on transoms with recessed tab pockets.
Scritto da: Paul W.
Awesome
Bought bolt rocker control(BRC4000) & plugged it in direct to actuators. Left the relay model off and works perfect! No need to cut or refigure wiring.
Scritto da: Noble S.
Really good
Easy to install and work great for my Sundancer260

Prodotti correlati

hot
Chiave e strumento per piastra di coperta per barche marine in acciaio inossidabile non magnetico universale Seachoice
3.5/5

€ 27.78

Chiave e strumento per piastra di coperta per barche marine in acciaio inossidabile non magnetico universale Seachoice
3.5/5

€ 27.78

hot
Attwood Attwood 66061-3 Tappo e catena di ricambio per riempimento di ponte in acciaio inossidabile si adattano ai riempimenti di coperta Attwood con una flangia da 3,5"
3.5/5

€ 54.96

Attwood Attwood 66061-3 Tappo e catena di ricambio per riempimento di ponte in acciaio inossidabile si adattano ai riempimenti di coperta Attwood con una flangia da 3,5"
3.5/5

€ 54.96

hot
Whitecap 60827 Modanatura per paratia in teak - Angolo esterno, binario da 3/4".
1.1/5

€ 43.08

Whitecap 60827 Modanatura per paratia in teak - Angolo esterno, binario da 3/4".
1.1/5

€ 43.08

hot
SeaSense 1/2IN OCCHIO DI PRUA/STERN
3.8/5

€ 45.76

SeaSense 1/2IN OCCHIO DI PRUA/STERN
3.8/5

€ 45.76

hot
Piatto piano ovale - bianco polare
0.1/5

€ 106.34

Piatto piano ovale - bianco polare
0.1/5

€ 106.34

hot
Occhio di prua in acciaio inossidabile Seachoice filettatura da 1/2" x 4-3/4".
3.8/5

€ 47.30

Occhio di prua in acciaio inossidabile Seachoice filettatura da 1/2" x 4-3/4".
3.8/5

€ 47.30

hot
Sea-Dog 327199-1 Morsetti rimovibili per montaggio su guida per tubi tondi
3.7/5

€ 75.11

Sea-Dog 327199-1 Morsetti rimovibili per montaggio su guida per tubi tondi
3.7/5

€ 75.11

hot
Old Cedar Outfitters Tagliere in plastica portatile
3.3/5

€ 40.66

Old Cedar Outfitters Tagliere in plastica portatile
3.3/5

€ 40.66

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart

Totale:€ 0.00

Vedi carrelloCheckout

Categorie

Tutte le categorie
Menu Categorie Cerca Carrello

Menu